--Make an Offer!--Liquidation Surplus Machine-- OMPEC TRO/10/R50 TYPE CE 3200 10-1/2' Hydraulic Veneer Guillotine, with 10° Cut & 50 mm (1.97") Fence Teeth Specifications: Max. cutting length 3,250 mm (127.95"), Nominal cutting length 112". Cutting width 23 - 1,020 mm (0.91" - 40.16"). Max. cutting height 80 mm (3.15"). Table height 950 mm (37.40"). Equipped with: 7.5 kW (10 HP) Hydraulic motor. Motorized parallel back fence, with 1/2 HP Motor, Digital readout, & Hand wheel for fine adjustment, and Parallel rack & pinion guides. 2-Handed operation & Safety light curtain. Complete with: Manual. Replaceable cutting pads. NOTE: Very well maintained, though machine has been stored outside under tarp, thus some surface rust can be expected.

RAIMANN Model ASA 1650, Veneer Patcher.Specifications: -- 61" Throat cap., 3 HP gear motor with new/rebuilt drive unit, strip type mechanical plug-feeder mechanism - cap. of up to (40) plugs/Min.; -- Thickness of veneer patchable 1/32" - 1/5" (0.08 mm - 0.2 mm) (softwoods), 1/20" - 3/16" (hardwoods). P-34 dies. -- Tool sequence: Veneer patch is cut by the table die and scrap is ejected into discharge chutes, veneer patch blank is then positioned against the underside of the table die, plug punch cuts replacement veneer patch from underside and patch is inserted into the proper position. -- Reconditioned by experts. -- Overall size: 10' 8" (3,250 mm) Length x 67" (1,700 mm) height; approx. weight 12,000 Lbs (5,450 kG). -- Optional Glue applicator add ...$9,975. -- Optional strip feeder add ...$6,750.Actual model is RAIMANN Model ASA 1650

SAVI HFK-250 Veneer Guillotine; General Specs: -- 102.4" (2,600 mm) Width cap., 4" daylight opening, hydraulically operated knife, 4 HP Leroy-Somer motor powers hydraulic unit with reservoir. -- Originally fitted with motorized parallel fence with 0.5 HP two speed gearmotor drive, push button operated, adjustable from 1" - 50" with magnified tape reader in front of machine. -- Equipped with: 2nd Cut feature with automatic reset, laser guide line light, photoelectric barrier guard for knife & hold-down beam, 2-hand operation of knife cycle. -- Note: Rear fence has been removed or modified. Shaft has chain/sprocket.

--In Auction--Starting bid: $100-- Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

VAC-U-CLAMP FT-1000 52" x 123" Dual Shuttle Table Thermofoil Vacuum Press Overall OEM Specifications: Typical cycle time 5.5 - 7 Min. averaging 7 - 8 Cycles/Hr., Approx. conservative production with 18 Parts/Cycle & 126 Parts/Hr., 1,000 Parts/Day, 5,000 Parts/Week. Table Configuration: (2) Shuttle tables (when one table is in press oven, other table is being loaded or unloaded), Table entry & exit completely automatic & powered by CNC-controlled gear-driven stepper motor. Construction: TIG-welded aluminum tubing covered with 18 GA steel covers that have been powder coated for durability, Aluminum platen easily removable for cleaning if necessary, Easy-access table 36" H. Heating: (24) 1000 W Quartz infrared type lamps, Infrared thermocouple for accurate reading film temperature. Features: Automatic film pressure bar opening/closing connected to safety circuit preventing table movement if bar is not completely closed, Automatic high pressure cooling air as tables exit from oven, Tempered glass viewing window with 300 W Interior halogen light. Includes: 45 CFM Vacuum Pump capable of producing near absolute vacuum (14.7 PSI, 29.9 in. Hg.), 30 Gallon ASME-certified vacuum reserve tank for rapid evacuation & decrease of cycle time, Vacuum lines rated for 3,000 PSI. Operator Controls: OMRON PLC Control, with Color touchscreen display, (5) Storage bays for different film type programs, & Remote access through built-in remote wireless modem. Complete with: (2) 61” W 3-tiered double-sided steel roll racks, Each with (2) Locking swivel & (2) Swivel 3-1/4” Dia. x 1” W Casters, Rack dimensions 76" x 32" x 41" H. NOTE: (1) Shuttle Table Not Installed & in Crate. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

102" Width cap. Veneer Clipper completely reconditioned to modern mechanical and safety standards to meet todays manufacturing needs. Original machine frame will be fully disassembled cleaned and repainted. The frame is the only part of the original machine used and all components are upgraded.Mechanical upgrades include:1. 2-Hand anti-tie back push button cycle activation 2. Photo safety eyes located on both front and back side of blade3. Full safety guarding including a fully enclosed knife section 4. New electric motor and gear box main drive system5. New knife and shear bar6. All new electrical/control box with Components and Wiring7. All new upgraded bearings including replacing Babbitt bearings Machine comes with a full (1) year warranty

CARGATE D-860 Rotary Veneer Lathe, Heavy Duty: -- Built specifically to handle large-diameter logs as well as small logs. It has a log length capacity of an easy 8'-6" and a diameter capacity of up to 5', peeling down to perfect 4" cores for optimal log utilization. -- This moneymaker looks like a big brother to a Premier Lathe. It comes complete with beefy Bull Gears and boasts plenty of output capacity along with the following main features and components:Specifications: -- BRUNETTE MACHINE WORKS Hydraulic Retractable Spindles - 4" inner, 8" and 11" outer. These are the same spindles as are utilized on a Premier Lathe. -- The spindles are driven by angle-cut 72" diameter Oil-Bath Bull Gears. (This is actually identical to an upgrade to Premier lathes still running.) -- Factory Hydraulic Backup Roll. (This backup roll rides on adjustable rollers riding down on top of the carriage. This prevents the backup roll from pushing excessively hard against the core. It produces perfect 4" cores).Equipped with: -- DURAND Charger and Pumps (self-centering). -- Factory Log Deck - Complete with S-drive and Gearbox. -- Factory Air Trash Gate, Infeed Conveyor (infeed to chipper). Infeed to PRENTICE Air Bag Clipper, Timing Wheel and Holddowns. -- Factory 5' Wheel, 6-knife, Veneer Chipper with Hold-down Drum Roller, and S-drive complete. -- 6' FERANO Chip Screen and Conveyor. -- Steel Framework and 450 FPM plus unwind speed!Highlights & Background: -- This lathe is capable of peeling very high production. In 1967 it was regularly peeling 225,000 sq. ft. 3/8 basis, or 400 - 500 cubic meters per 8-hour shift. The lathe is in wonderful overall condition and portions can be turned on today although it has not seen service since 2005. When you think "CARGATE" think "big PREMIER" and you will have the right idea.Price shown is in US Dollars. - Experienced Owner is flexible to assist in removal and perhaps installation.

COE 249D Veneer Lathe with the following: -- 27" maximum log diameter, Approx.110" knife length. -- 1484 Veneer Lathe Big Bar. -- 1390 Veneer Lathe Core drive. -- 3 to 1 inner drive ratio. -- Capable of peeling approx. 35 cubic meters per hour. -- Includes: • Linden step feeder• Small log offset x-y spindle chucks• 27"; maximum log diameter• 1484 big bar• 3 to 1 inner drive ratio• Digital ball feed carriage drive -- Note: Sold without 'charger or drive' included. -- This COE Veneer lathe line was completely rebuilt and installed in 2006. The lathe was operated less than one year and is reportedly in very good condition.

COE 233 Rotary Veneer Lathe. -- 30" Swing and 44" Knife length., -- Turning motor LINCOLN 50 HP 230/460 -- Complete with: Hydraulic unit, all drive motors and controls. -- Includes: veneer knife. - Ideal for peeling short blocks.

LANGZAUNER G-5920 Cross-Cut Guillotine. Specifications: -- 35.5" Blade hydraulic pressure bar and knife; -- 5 Gal tank, pump is driven by 1.5 HP motor.Complete with: -- 2-Hand operation or foot pedal, Emergency-Stop, (3) photocells for safety, -- All safety guards per international standards.

MARUNAKA Model RD – 8J WIDE Single Deck Veneer Roll Dryer;Complete with the following features: -- 1988 - year of manufacture. --Working width – 51"; --Length of the dryer – 24 Ft (4 Sections) --Type of heating - Steam --Operational in 2018 when mill closed --Professional rigging and loading available.

MARUNAKA Model RD-3UB/RD-6UB (Connected) Single Deck Veneer Roll Dryer;Complete with the following features: -- (3) 3 HP circulating fans with (1) 3 HP exhaust blower thru the ceiling. -- Optional heat source: electric (7) Elements/Zones, computer controlled thermocouples in addition to (2) Natural gas burners (OEM).. Both dryers have a 100amp circuit breaker with 100amp fuses. The RD 8 operates with 4 fan motors and 4 heaters. The RD 6 has 3 fan motors and 3 heaters";.. -- Capable of temperatures to 120° Celsius (250° Fahrenheit). -- Working width 1000 mm or about 39 inches. Veneer is fed endo.Please Note: -- Dryer is (2) separate units; all equipment will fit into a 40' container for shipment from Eastern USA. -- All equipment is in good working condition including all fans and blower, temperature control works properly; feed roll drive works well. -- Rolls have been nickel treated to minimize corrosion/oxidation. -- This dryer equipment is still in place. -- MARUNAKA (2) Models: RD-3UB and RD-6UB currently connected to increase capacity. Can easily be separated.NOTE: Refurbished in 2005, operated from 2005 - 2012. Still operational ready to work!