PMK C 1205 Single End Coping Machine -- With the C-1205 Coping Machine you can run your Styles first or run your cope first, this machine using a 7.5 HP motor has counter rotating spindles to insure Chip free coping of either square. -- Single profiled or double profiled parts. Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 13.5" wide on the C-1205. -- Two counter-rotating spindles 1.25" in Diameter. -- Capacity of maximum (2) cutters on stack tooling -- Spindle Speed 7,000 RPM; cycle time approx. (4) Seconds. -- Side Pressure Clamp to insure proper alignment with a fence. -- Cutter Heads totally enclosed for Safety!

PMK C 1203 Single End Coping/Tenoning Machine -- With the C-1203 Coping Machine you can run stiles first or cope first, this machine using a 5 HP motor has counter rotating spindles to insure chip free coping of either square, single profiled or double profiled parts. -- Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 9.5" wide on the C-1203. -- (2) Counter rotating spindles 1.25" diameter. -- Spindle Speed 7,000 RPM; cycle time approx. (4) seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety!

PNEUMAFIL 13.5-460-8 Reverse Air Dust Collector System;Reverse Air Dust Collector with 42,600CFM at 9 to 1 air cloth ratio, 4,738 square feet of filter area. -- 13-1/2' Dia. round baghouse contains (460) bags - 96" long by 5" dia. filter bags in galvanized cages w/reverse jet bag cleaning. -- Reverse Air from 15 HP blower motor which cycles once a minute over filter bags (rotating plenum covers each row of bags once a minute, reversing the normal air flow direction. -- Reverse Air action back flushes the bags and dislodges wood dust particles collected on the filter media which then fall to the bottom of the 60° funnel hopper for removal), bags are changed via walk-in door.. -- Material handling fan with approx. 48" inlet dia with 150 HP floor mounted motor (covered in a shed); 0.25 HP explosion proof motor for manifold drive. -- Rotary Air Lock, gearmotor driven at the bottom of the hopper feeding and shared horizontal screw type auger (if you want it) with gearmotor drive. -- Features: MOTOTRONICS Soft Start for main motor. FIRETEK Spark Detection System (subject to prior sale with adjacent unit). -- Includes: Explosion doors, sprinkler pipe, interior electrical control panel, support frame, safety ladder, railings, and exterior ductwork.Professional dismantling, rigging, transport and installation is available.NOTE: Unit being sold under this record is pictured on the left side on the first two photos. For the smaller diameter unit on the right side (DIXIE AIR) see record "DO-011266".

POWERMATIC - 26, ...Single Spindle Shaper -- Specifications: 5 HP (3.7 kW) - 3,600 RPM Belt drive motor; 7,000 & 10,000 RPM spindle speeds via 2-speed step pulley; reversing switch. -- 1" Dia. solid interchangeable spindle featuring 3-7/8" cap. under the nut; 3" spindle travel w/handwheel adjustment -- Complete with:24" x 26" Cast iron table; miter slot; 7" insert opening; adjustable fence; magnetic controls. -- Actual Model is: POWERMATIC 26

POWERMATIC 225 STRAIGHT KNIFE PLANER24" x 8" Cap., 7.5 HP direct drive cutterhead motor, BYRD Spiral cutterhead.1.5 HP drive motor, variable feed speed from 20 - 100 FPM with forward/reversing switch. -- Features: sectional serrated infeed roller and sectional chipbreaker, (2) adjustable powered bed rollers; table size 24" x 48", with manual height adjustment. --Complete with: Magnetic motor controls & 8" dia. dust hood. Fully rebuilt recently and equipped with a BYRD Spiral cutterhead!

POWERMATIC TS29 TILING SPINDLE SLIDING TABLE SHAPER WITH 4 ROLL FEEDERSolid construction & design for any job from the largest to the smallest. -- Fully enclosed fabricated steel base to minimize sound level & vibration. -- Oversized 33-1/2" x 51" cast iron table with 11" x 51" sliding table that is supported by (6) tapered precision bearings. -- Sliding table with miter head, holddown & fence to accommodate numerous applications from end cuts to tenons. -- Fully adjustable rear fence with extruded aluminum face & accurate mechanical digital readouts on either side for fast & accurate setup to increase repeatability. -- 7.5 HP motor drives an extra large quill assembly with (3) oversized bearings to accept a variety of interchangeable spindles & router collets. -- Long 7" vertical spindle travel to allow the operator to stack tooling, 6-1/4" under the nut. -- Spindle capacity 3/4", to 1-1/4" -- (5) Spindle speeds in forward & reverse to provide the correct speed for any application (3000,4000,6000,8000,10000 rpm). -- Multiple table inserts for max. 9" opening for straight & tilting arbor operations which allow for virtually any size cutter. -- Arbor tilts 5°back and 45° forward for increased versatility with tooling. -- Large scale "ACCU Fence" with integrated dust collection shroud & cutterhead guard. -- AMBI-TECH Electronic brake. -- Clamping miter gauge. -- Push button magnetic control.

POWERMATIC 100 Single Sided PlanerSpecifications: -- 12" Cap. with 1/16" to 5" thickness opening -- 5 HP motor - 5,300 RPM -- 3-knife cutterhead with high speed steel knives -- 3-1/8" dia. head; 18 FPM fixed feed speed. -- Solid infeed rolls; 12" x 24" precision ground cast iron table. -- 1/4" max. depth of cut -- 7-1/2" min. stock length (unbutted). -- Complete with: Magnetic controls, cutterhead guard with dust chute on enclosed steel stand. -- Belt driven head

POWERMATIC 221 PLANER WITH BYRD HELICAL HEAD20" x 8" Cap., 10 HP TEFC belted drive motor, BYRD Helical cutterhead, hand wheel micro-adjust table; 1 HP feed motor for variable speed from 20 - 50 FPM, segmented infeed roll and sectional chipbreaker, 4" dia. smooth outfeed roll. -- Complete with: Magnetic starter and dust hood.

POWERMATIC KUFO 1632 (KUFO SK-15A) Wide-Belt SanderSpecifications: -- Open-sided single head 16" Wide Belt Sander. -- Open-sided design to allow up to 32" wide workpiece in (2) passes. -- Combination head with a 4" diameter rubberized contact drum. -- Head with a finishing platen. -- 5 HP Single-phase or 7.5 HP 3-phase motor. -- Air abrasive belt tracking. -- Manual readout to reference the 0" - 6" thickness setting. -- Center jack to set bed location. -- 0.25 HP Conveyor drive with 20 FPM. -- (2) Infeed & (2) outfeed spring loaded holddown rollers. -- Side extension support, load meter and safety shutoff. -- Operators manual.

POWERMATIC - RB-37, ...Single Head Wide Belt Sander1-Head, 36" width cap., combination sanding head. -- Includes: 4" Dia. contact roll & 2" wide polishing platen, micro-adjust platen; 15 HP main motor. -- Abrasive belt size: 37" x 60"; with air tensioning, air jet abrasive belt tracking.1 HP Feed drive; variable feed speed of 15 - 30 FPM conveyor speed.0" - 5-1/4" Opening with: (4) Screw jacks; double infeed & outfeed rubber covered holddown rolls. -- Complete with: Magnetic starter; overload protection; load meter; emergency brake.

POWERMATIC MODEL 100 PLANER12" Cap., 5 HP 5,300 RPM belt driven main motor, 1/16" to 5" thickness opening, 3-1/8" dia. 3-knife cutterhead with high speed steel knives, 18 FPM fixed feed speed with in-out clutch -- Corregated infeed rolls; 12" x 24" precision ground cast iron table. 1/4" max. depth of cut, 7-1/2" min. stock length (unbutted). -- Complete with: Knife grinder, Magnetic controls, cutterhead guard with dust chute on enclosed steel stand.

POWERMATIC Turbo Cone Dust Collector with Twin Canister Filter Kit;Complete with the following features: -- 3 HP 3 PH Material Fan, -- Generates 1,782 CFM. -- Ships from Oregon Coastal region.

20" Dia. dynamically balanced aluminum disc, 3 HP - 1,740 RPM direct drive motor; 15" x 27-1/4" table w/miter gage slot, tilts 30° upward & lowers 45° downward, 90° positive table stop; rack mechanism for raising & lowering table by hand crank, heavy bolt-down steel base. Complete with reversing switch and miter gauge. Also available in Single-phase in 2 HP motor.

POWERMATIC - WB-25, ...Wide Belt Sander1-Head; 25" width capacity; 1/8" to 6" thickness capacity.Combination sanding head with: 4" Dia. rubber-covered contact roll; 2" wide polishing platen; micro-adjust platen; steel abrasive belt tension roll; steel idler roll: 25" x 75" Abrasive belt capacity.Equipped with: -- 15 HP 3-Phase main motor; 1 HP variable feed motor, 15 - 49 FPM. -- 1/4 HP Table raising & lowering motor with: Auto adjust thickness assist; 1/8" to 6" opening with (4) screw jacks. -- Double infeed & outfeed rubber covered holddown rolls. -- Complete with: -- Digital readout; air eye belt sensing; limit switch overtravel protection; magnetic starter; overload protection; load meter; emergency brake.Includes: Owner's manual & parts list.

POWERMATIC - 28, ...Shaper1-1/4" Dia. spindle; 7-1/2 HP - 3,600 RPM motor; 3,300 - 9,500 RPM spindle speeds via Factory installed Variable Frequency Drive.4-3/4" Cap. under nut when using the 1-1/4" spindle; spindle brake; 30" x 39" table.

POWERMATIC - TS-80, ...Single Spindle ShaperAccepts: 3/4" - 1" - 1-1/4" Dia. interchangeable spindles; 5-1/2 HP motor; 3,625 - 5,000 - 7,250 - 10,000 Spindle speeds. -- 4" Cap. under nut when using 1-1/4" spindle; 6-19/64" spindle stroke; approx.: 39-1/2" x 31-1/2" Extra thick cast iron main table. -- Complete with: Adjustable split fence; spring holddowns; removable table inserts; dust collection shroud; reversing switch; spindle brake; cutterhead guard. -- Includes: Infeed & outfeed tables shown in picture. - NOTE: Needs some work on bearings.

POWERMATIC - 26, ...Single Spindle Shaper -- Specifications: 5 HP - 3,600 RPM belt drive motor; 7,000 & 10,000 RPM spindle speeds via 2-speed step pulley; with reversing switch. -- 1" Dia. solid interchangeable spindle; featuring 3-7/8" cap. under the nut & 3" spindle travel w/handwheel adjustment. -- Complete with: 24" x 26" Cast iron table w/miter slot & 7" insert opening. -- Equipped with: Adjustable fence and Magnetic controls. - 4-Roll 4-speed Power Feeder.

POWERMATIC Shaper PM 2700, Spindle Shaper model 128-0102C 5 HP, Single Phase, 230 V - 1280101-CSpecifications & Features: -- Digital readout gives the use of exact spindle height and allows for 0.001" adjustments. -- 4" Spindle travel. -- 5 HP Motor -- Heavy-duty 30" x 40" precision ground tabletop for smooth stock feeding and Heavy-duty cast iron base. Includes: -- 3/4" and 1-1/4" spindles -- Independently adjustable fence sides. -- Micro-adjust control knobs allow for precision adjustment for the fence. -- Integrated casters can be raised and lowered to mobilize shaper. -- Superior clear cutter guard promotes safety, allows observation of the entire cut. -- Table predrilled and tapped for Power Feeder mounting.Dust Collection Minimum CFM Required (CFM) 600; 4"Dust Port Outside Diameter

POWERMATIC Shaper TS-29, with Sliding Table & Tilting SpindleSpecifications: -- 3/4", 1", & 1-1/4" Dia. interchangeable tilting spindle, 3/8" & 1/2" collet & router bit adapters, tilts 45° forward and 5° back, 7-1/2 HP - 3,600 RPM motor; 3,000 - 4,000 - 6,000 - 8,000 - 10,000 RPM spindle speeds via 4-step V-pulley with "quick release". -- 4-3/4" Cap. under nut when using the 1-1/4" spindle, 7-1/16" spindle travel; 51-1/2" x 33-1/2" extra thick cast iron main table, (3) removable table inserts 2-1/2" - 5-1/2" & 5-7/8" x 4-3/16" (oval).Complete with: -- Large scale "ACCU Fence" with integrated 4" dust collection shroud, reversing switch, AMBI-TECH electronic brake, cutterhead guard, clamping miter gauge & magnetic control; incl. owners manual & parts list. Actual Model # 1791284

POWERSCREEN TRAKPACTOR 500 TRACKED IMPACT CRUSHER (DIESEL) --Features: 500 HP Scania DC13 385A Engine; Umbilical and Wireless Controls; 500 Tons/Hr. Output Potential (depends on size/type); --Specifications: 16' x 5' Post-Screens and Fines Conveyor with 12'7" Discharge Height; 16'3" x 8'7" Hopper; Working Dimensions: 56' x 9'10" x 13'6"; Transport Dimensions: 56’8";x 9’10";x 12’6";; Weight: 115,919 Lbs. --Hours: Approx. 9,600 --Seller States: Starts, runs, and operates like it should; Recently serviced on 9/17/24 at 9,579 hours; Belts and rollers in good condition. --Contact Us for Competitive Leasing Options. --All equipment is advertised to the best of our knowledge and everything is sold “AS IS"; with no guarantees.#Powerscreen #ConstructionEquipment #ImpactCrusher