CAM-WOOD SM-732 HS 7-Heads High-Speed Trough Feed Moulder(7) Heads (B-R-L-T-T- T-B), working cap. 111 13/16" x 6-1/4"".Specifications: -- Max/Min working width 11 13/16" - 3/4" -- Max/Min thickness 6 1/4" - 5/16" -- Minimum length 9-1/2" -- Head sequence: Bottom 20 HP, right 15 HP, left 15 HP, top 20 HP, top 20 HP, top 15 HP and bottom 15 HP motor. -- All Horizontal spindles have outboard bearings -- Spindle dia. 50 mm with cutterhead speed of 6,000 RPM. -- All spindles are equipped with mechanical digital readouts, "Dual mechanical" readouts on the left and top spindles. Mechanical readouts for pressure elements and chipbreakers; all chipbreakers and pressure elements with pneumatics. -- Feed works: Inverter driven 15 HP feed system with feed speeds of 20 - 260 FPM. -- Infeed table 2M (6'6"), chromed tables, and fences. Side pressure roller mounted at infeed. Features and complete with: -- PNEUMATIC LOAD INFEED SIDE PRESSUREWhile high speed feeding, the side pressure on infeed table ensures every timber close to the fence even under different width. It's convenient to adjust quickly. --OVER HEiGHT PROTECTIONIn case workpiece exceeds the rated maximum height, it will be restricted by the over height protection device provided at the workpiece infeed end. -- HYDRAULIC OUT-BOARD BEARING SUPPORT TOP AND BOTTOM SPINDLESpecially designed hydraulic supports on the top and bottom spindles assure maximum stability while performing high speed and heavy duty machining. -- PNEUMATIC LOAD SIDE PRESSURE WHEELS The front side air pressure wheel on left vertical spindle fully eliminates problem when feeding short or narrow stock not smoothly. The pressure plate is easy and quickly to adjust. -- PNEUMATIC LOAD TOP PRESSURE PLATEThe front pressure plate for top spindle is available to apply an air loading device ensuring maximum stability while performing high speed cutting -- CENTERAL LUBRICATION POINTThe lubrication point are located at the centralized plate for convenience. -- POWERED INFEED TABLE ROLLER The roller in the infeed table is powered, providing a smooth feeding effect for feed stock. -- VERTICAL SPINDLE AXIAL ADJUSTMENT UP TO 60MMIt allows fitting several tools on the vertical spindle, eliminating troublesome cutter change. The 60mm spindle adjustment provides full utilization for a single cutter. -- CENTRALIZED PRESSURE ADJUSTMENT• All pressure regulations for the entire pneumatic system are centralized at the front of the machine for added convenience in pressure adjustment, and sectional pressure adjustments for all pressure rollers ensure consistent pressure.• Clear numerical indicators are provided to correspond directly to the pneumatic mechanisms on the machine, allowing operators to make adjustments based on different processing requirementsAvailable options: -- Automatic Jointer for all (6) heads add: ...$45,600 -- Digital (electronic) display for X and Y axis for each head add $ 3,200 /per head -- NC Automatic positioning control sys

CAM-WOOD SFJ-300A End Matcher, 12" Performs tongue and groove, tenoning, mortising, and shaping at both ends of the boards; -- Includes 10'-6" Powered Infeed and 7' Non-Powered Outfeed Conveyors. -- Air-operated hold-downs keep material firmly in place during the machining process. -- Cutter heads move in and out while cutting a tongue on the trailing end of one part and a groove on the leading end of the following part.FEATURES: -- PLC controls combined with a touch-sensing screen for maximum convenience of operation. -- Each cutter head is driven by a separate motor driving the spindle at 7,500 RPM spindle speed. -- Accepts unlimited wood lengths via an automated conveyor for infeed and outfeed processing. -- Cutterheads feed thru the wood is controlled by a frequency inverter that permits speed changes to suit various cutting conditions. -- Pressure plates are actuated by air cylinders. -- Hard chrome-plated table features maximum wear resistance. -- Table rollers increase feed smoothness. -- Powered in feed roller conveyor is driven by a 1 HP motor. -- 3,400 mm in feed roller conveyor and 2,200 mm out feed conveyor table are standard equipment. -- Fully enclosed chip guards. -- Air-operated clamp holds stock firmly in place. After the workpiece is clamped, the cutter head moves in and performs the shaping operation. -- The spindle is precision constructed to cut accurately -- The spindle height adjustment is displayed on a dial gauge. -- CAM-WOOD’S 2-spindle design accommodates cutterhead dia. up to 6"; -- When end matching, one spindle cuts the tongue, and the second cutterhead machines the groove. SPECIFICATIONS: -- 1-1/2" To 12" width cap. -- 10-1/2"; min. length cap. -- Thickness 3/8" to 1 3/8" -- Unlimited length, no restriction. -- Material feed speeds up to 297 FPM; cutterhead travel speed of 79 FPM -- Cutting cycle time 1.5 second.and up to 20 cycle per minute -- (2) 5-1/2 HP Spindle motors and a 2 HP feed drive -- 1/2 HP motor for in/out cutterhead travel. -- 40 mm Dia. spindle -- Requires 1300 CFM dust collection.

CAM-WOOD 16' Pusher Type Cutoff Saw with Crayon Marking connected to a CAM-WOOD 12" wide End Matcher; System width capacity is 12" with a maximum inbound board length of 16' (as priced here). 8' and 12' Saws are also available. Call Jeff for price deduction.General Data: -- Cut-Off Saw is arranged to remove defects from Clear. Will chop for random length clear material OR optimize clear wood according to your cutlist, delivering either to the End Matcher. -- The line requires (1) man to mark and feed the Cutoff Saw and (1) man to offbear and stack finished work coming from the End Matcher. Price includes the following equipment and specifications: Defect Saw Features: -- 18" CAM-WOOD Model CS-18AAT-16' Automatic Cut Off Saw equipped with Automatic Pusher for increased automation and efficiency -- 16' Infeed table -- Works as an automatic pusher for defect removal and fixed length cutting when crayon marking -- PLC controlled automatic pusher device is driven by servo motor at feed speeds up to 200 FPMAutomatic Pusher Operation: -- Operator places crayon marks at the leading and trailing ends of a defect or waste zone (Optional) -- Pusher moves the board to the first crayon marked defect, automatically completes the cutting cycle, and continues to position and chop the board at each crayon mark, thereby removing all waste zones. When the board is finished, the pusher returns to its starting position at top speed and starts on the next board -- Super Pusher travels up to 200 FPM -- Sealed, long-life ball bearings -- Precision ground cast iron table with heavy metal stand -- Easy to operate in all operations -- Saw blade comes up from beneath the table and returns after cutting for safe operation -- Totally enclosed blade guard prevents danger during cutting cycle -- Includes magnetic starters with overload protectionCutting & Other Specifications: -- (45) Strokes/Min -- 18"; Saw Blade Diameter with 1"; Saw Arbor -- 10 HP Arbor Motor -- 3,200 RPM Blade Speed -- 90 PSI Compressed Air requirement with 1" Inlet -- (1) 4"; Dust Hood -- Machine Size (W x L), 30" X 28-1/2'Automatic Transfer between Defect Saw and End MatcherCAM-WOOD SFJ -300 End Matcher with the following Specifications: -- Machines tongue and groove at ends of random or fixed length boards as provided by the Defect Saw -- Includes powered conveyor for infeed and steel landing table at the outfeed -- Air operated hold downs keep material firmly in place during the machining process -- Cutter heads move in and out while cutting a tongue on the trailing end of one part and a groove on the leading end of the following pieceFeatures: -- PLC controls combined with touch-screen for maximum convenience of operation -- Each cutter head is powered by a separate motor driving the spindles at 7,500 RPM -- Accepts unlimited wood lengths via an automated conveyor for infeed and outfeed -- Cutterhead travel thru the wood is controlled by a VFD which permits automatic speed changes to suit various

Costa S6 XUT 1350 3 Top Head Wide Belt Sander53" Width cap, Crossbelt, Combination Head, PlatenHead Configuration1st Head :Transverse Belt Unit -- Transverse Belt Width: 5.9"; (150mm) -- Transverse Belt Motor: 14.75 HP (2nd Head: Combination Roller-Rad, Steel Roller3rd Head :Segmented Pad Unit with Superfinishing Belt, Motor Power: 20 HP (15 kW)Specifications -- Max. Sanding Width: 53.15"; -- Sanding Belt Width: 54"; (1380mm) -- Min. Sanding Thickness: 0.12"; -- Max. Sanding Thickness: 6.3"; -- Vacuum belt with fixed pass height -- Feed Belt Speed: variable up to 82 ft/min. -- Feed Belt Motor: 3 HP (2.2 kW)Equipped with & Features -- Top brush on the outfeed -- Single 3kW fan for vacuum feed belt -- Machine Programming Software: LOGIC A -- Total Installed Power: 112 HP (83 kW)

COSTA KH2 CCCT 1350 Wide Belt Sander, (4) Heads52" Width cap. Drum, Drum, Drum, PlatenHead Configuration:1st Head: Steel contact roll, 9-7/8" dia, 45 HP motor;2nd Head: Rubber covered contact roll, 9-7/8" dia, 45 HP motor.3rd Head: Rubber covered contact roll, 9-7/8" dia. 60 shore, 30 HP motor.4th Head: Finishing Platen, 23 HPSpecifications: -- 53" x 103" Abrasive belts, air blast abrasive belt cleaning, pneumatic belt tensioning with electronic tracking. -- Controls with PLC processor, -- Pneumatic grit compensation with 4-position stops. -- Variable feed speed conveyor with inverter control 16 - 82 FPM.Equipped with & Features -- a Vacuum conveyor bed assembly with a 5.5 HP suction fan and motor. -- Infeed & outfeed spring loaded hold down shoes on all heads. -- Powered raise & lower conveyor bed with LED readout and motor load meters.

COSTA - KK CC-CCC 1350, ...5-Head Top & Bottom Wide Belt Sander.53" Width capacity; (2) Bottom drums, (3) Top drums.Bottom Machine: -- Constant pass line height: 1,000 mm (39"). -- Motorized infeed conveyor. -- Motorized infeed pressure rollers. -- Sectioned infeed pressure beam.1st Head: -- Rubber covered cylinder ,16" dia., 35 kW motor. -- Intermediate pressure shoe with lips and rubber covered rollers.2nd & 3rd Heads: -- Rubber covered cylinder, 16" dia. (2nd head), 52 kW motor (3rd head), 88 kW. -- Outfeed pressure shoe with lip and rubber covered rollers. -- Vacuum Feed Table: 10 HP (7.5 kW) motor. -- Vacuum set pneumatic for (2) levels of vacuum pull control.Top Machine: -- Infeed roller. -- Motorized infeed pressure rollers. -- Sectioned infeed pressure beam.1st Head: -- Rubber covered cylinder, 16" dia., 35 kW motor. -- Intermediate pressure shoe with lips and rubber covered rollers.2nd & 3rd Heads: -- Rubber covered cylinder, 16" dia. (2nd head), 52 kW motor (3rd head), 88 kW -- Outfeed pressure shoe with lip and rubber covered rollers. -- Vacuum Feed Table - 10 HP (7.5 kW). -- Vacuum set pneumatic for (2) levels of vacuum pull control..Equipped with and Features: -- All drives are equipped with disc brakes. -- Each Sander with vacuum feed belt with fans..

CAN-PAK - CD-3000: Complete Can Densifier -- Motor: 25 HP.Dimensions• Height: 9’-2";.• Width: 3’-10";.• Length: 13’-5";.• Machine weight: 8,000 Lbs.• Conveyor weight: 1,000 Lbs.• Conveyor: 11’-5"; High x 20-1/2"; wide x 13’ long.Specifications• 25 HP Power unit.• 460 Volt, 3-phase wiring.• Solid-state programmable controller.• Thermostatically controlled hydraulic oil cooler.• 1 Cubic yard hopper.• 120-gallon hydraulic tank.• 20-1/2"; Wide infeed conveyor with: 3/4 HP Motor. Direct drive gear reducer. Magnetic head pulley. Steel reject chute.

CP MANUFACTURING - S100-6-LH-US, ...Screens -- (1) System of (2) Screens -- Very lght Use -- Ordered as part of a Single-Stream Sort System that was designed to run 10 Tons/Hr -- 1-Feed Conveyor -- Each: 14,500 Lbs -- Loaded onto your Truck

CP MANUFACTURING - OCC4, ...Fiber Screen Sorting SystemEfficient screening technology for separating 2D & 3D materials.Specifications: -- Capacity: 10 to 12 Tons per hourEquipped with: -- Double OCC -- Fiber screen -- Glass breaker -- Post sort -- Bunkers -- Mezzanines -- Misc. spare parts -- All manualsNOTE: Complete System with low hours!

CP CD1000 CAN DENSIFIER -- 900 to 1,500 Lbs/Hr capacity -- Fully automatic solid-state Controller -- Density: 40 Lbs per cu. ft. allowing 140,000 Lbs in 50' railcars or 40,000 Lbs in 40' Trailers. -- 10 HP 3/60/208/230/460 Volt Hydraulic Power Unit

CP MANUFACTURING - GC100, ...Glass CrusherThe "GC100" crushes up to 7,000 pounds of glass per hour.Specifications: -- A tough, PVC-cleated belt carries the glass up the conveyor, allowing for visual inspection before it enters the crushing chamber. -- It efficiently handles up to a 4-liter container, breaking it into approx. 1-inch pieces of recyclable cullet; that lets you reduce your volume, easily fill your shipping containers - and ship maximum-weight truckloads to reduce your freight costs. -- The "GC100" works and keeps on working. It features cast chromium alloy steel crusher bars that are extremely resilient. It has a completely replaceable crushing drum liner. -- It is constructed of durable, heavy gauge steel. All you need is 115 115-volt single-phase power.FEATURES:• Heavy gauge steel construction• Cast chromium steel crusher bars (4 crusher bars included)• Replaceable crushing drum liner• Removable catch tray• Forklift slots• Shaft-mounted conveyor speed reducerCAPACITY: • Up to 7,000 Lbs/hour • Up to (600) cases/hourSPECIFICATIONS:• 4’-2"; Discharge height• 115 Volt single-phase wiring• 1/3 Cubic yard hopper• Mounted on 8"; casters• 0.5 HP Crusher motor• 0.5 HP Conveyor motor• 15’ Wide PVC cleated conveyor beltDIMENSIONS:• Height: 8’• Length: 3-3/4’• Width: 4’• Conveyor belt width: 15";• Hopper width: 6";• Weight: 1,000 Lbs

CRAFTSMAN DP-65 Drill PressSpecifications: -- Capacity: 15" -- Motor: 0.33 HP Equipped with: -- Push button control -- Stand

CRAM-A-LOT - HX-60: Closed Door Baler with Cart Dumper & Infeed ConveyorSpecifications: --The CRAM-A-LOT "HX-60 HH" & "HX" Series Balers are ideal for warehouses and designed for ease of installation, operation, and maintenance. -- CRAM-A-LOT® HH & HX Series Balers are: Built with extra Heavy-Duty construction; ideal for warehouses & recyclers who deal with large quantities of corrugated and paper products.Baler is designed for long hours of operation and can operate either manually or automatically with photocell control. Optional custom-engineered Feed Conveyors and Cart Dumper Systems efficiently control Baler feed rates for optimum performance in a complete Baling System.Standard Features include:ANSI Z245.5 Compliant: All Compactors meet or exceed ANSI Z245.5 safety standards.UL/CUL Listed Control Panels.UHMW Ram Shoes: Adjustable to assure straight tracking and readily replaceable, should the need arise.Oil Sight Gauge: Oil level at a glance.Oil Filter: Replaceable "spin-on" cartridge to keep your oil clean.Heavy-Duty Controls: NEMA 4-Rated pushbutton controls with "key lockable" start switch.Automatic single-cycle operation. -- Bale Size: 60" x 30" x 40". -- Bale Weight: Up to (OCC) 1,400 Lbs. --Throughput: (OCC) 2-1/2 Bales /Hr. -- Cylinder: 7".

CRAM-A-LOT - SCR-T2-34: (3) 34-Yard Self-Contained CompactorsNOTE: Lot of (3) Specifications: -- Cylinder: (2) 4". -- Main motor: 10 HP. -- Feed opening: 41″ x 58″ (1,041 mm x 1,473 mm). -- Capacity: 34-Yard. -- Ram force: Up to 24 tons.

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6k ROCKWELL/CRESCENT 5-Head Single Head Tenoner Equipped with: Manually-operated sliding table. (1) Top & (1) Bottom Tenon Heads, Each with 2 HP Motor, (1) Top & (1) Bottom Cope Heads, Each with 1 HP Motor, & (1) 7" Cutoff head with 1 HP Motor.

CRESCENT P 24 PLANER -- 24" x 8" Cap., 10 HP direct drive motor. -- 4-Knife cutterhead, approx. 11" min. un butted stock length. -- 24" x 36" (Approx.) Cast iron table, manual raise-and-lower. -- 1 HP Separate feed motor, variable speed from 20 - 50 FPM; (2) 3-5/8" dia. powered bed rollers, (1) 3-5/8" dia. upper outfeed roll, and sectional infeed roll with (12) 2" sections. -- Features: Sectional chipbreaker with (12) 2" sections.

CROUCH - 250-F, ...Edge Sander37" x 6" Graphite coated platen; 2 HP motor. -- Equipped with: 9" x 36" Side table with adjustment; 10" x 32" end adjustable table.

CROUCH - 81-70 ...Edge Sander (Non-Oscillating)5 HP Direct drive motor; 6" x 144" abrasive belt size; (1) 8" x 56" Platen.Equipped with: -- (1) 12" x 56" Adjustable side table and (1) 15" x 28" end table.Tables adjust vertically 5" and laterally 2-1/2". -- 8" Dia. rubber covered drive pulley and 4" dia. aluminum idle pulley.

CROWN RC3020-30 Stand-Up ForkliftSpecifications: Load Capacity: 3,000 Lbs -- 3-stage mast -- Max. lift height 190" -- Clearance height: 89" lowered -- Battery drive train: 24VEquipped with: -- Side shift -- cushion tires -- Overhead guard -- Power steering and SCR travel controllerNote: Charger is optional.

CSMI Hi-Tech Optimized Board Edger. Complete with the following features: -- Two-saw Edger. --Top reman Head and System. --Infeed. --Unscrambler. --Scanning and Optimization. NOTE: Offered earlier at $75,000.