704-841-2001
Backed with a massive machinery database considered to be “the blue book” of woodworking machinery), EX-FACTORY Auctions provides a complete assessment of your equipment and allows you to interact with the market real-time in our dynamic Online Auction!
1823 Results Found
704-841-2001
SAS SCORPION ENGINE PULLER Model SC40 DescriptionIncrease cash recovery from your recycling operationsSAS Forks Scorpion High Speed Motor Puller – Scrap Yard Engine Puller – Auto Recycling Engine Puller – Excellent for self service yards processing vehicles before crushing.Generate revenue:Process end of life vehicles in less than 60 seconds.Pull scrap engines and transmissions in 30 seconds.30% more revenue by separating metals from bodies.1000% more revenue per lb. on wire harness from engine compartment and dash.80% more visibility with a direct line of site from the operator’s window through the forks.Cycle time less than 15 seconds from park to full extension.Serviceable for long life. Replace blades in 3 hours or less.estimated only.Engineered & built for optimum performance:Engineered tough for continuous prying and durability.Hardened pins and bushings and grease-able pivot points for extended service life.Hydraulic hoses and cylinders are protected to minimize potential damage from sharp objects.Built with high strength blades and carriage skid plates for extended service.Clean up of ground debris is a snap with center plow blade.Speed is paramount in this design. Operator uses grapple from the cab, no torches, no personnel needed to hook up chains to pull or move engines. Safer, quicker and less costly removal of engines and transmissions.
Saturn Model 36x20 Slow-Speed Shredder --36" long x 20" wide chamber opening --1/2" knives. -- KYB MRH-30-SW2 hydraulic system powered by a 50-hp three-phase electric motor. --Comes equipped with stand and controls. -- Excellent for plastic, E-scrap, rubber, small tires, paper, cardboard, light metals.
Call for Price
SAVI HFK-250 Veneer Guillotine; General Specs: -- 102.4" (2,600 mm) Width cap., 4" daylight opening, hydraulically operated knife, 4 HP Leroy-Somer motor powers hydraulic unit with reservoir. -- Originally fitted with motorized parallel fence with 0.5 HP two speed gearmotor drive, push button operated, adjustable from 1" - 50" with magnified tape reader in front of machine. -- Equipped with: 2nd Cut feature with automatic reset, laser guide line light, photoelectric barrier guard for knife & hold-down beam, 2-hand operation of knife cycle. -- Note: Rear fence has been removed or modified. Shaft has chain/sprocket.
$3,250
SAWSTOP - 10", ...Table SawSpecifications: -- 10" Blade cap.; 3 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor diameter. Features: -- Enclosed cabinet, Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: -- 50" Rip fence; side support table and laminated top; 4" dust collection port. -- Magnetic contactor motor control; main power switch with removable lock-out key. Actual model #: ICS 31230
$3,900
SAWSTOP - ICS 73230, ....Table Saw w/Safety "Stop Feature"Specifications: -- 10" Blade cap.; 7-1/2 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor dia. -- Features: -- Enclosed cabinet; Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: -- 52" "T-Glide" rip fence system; side support table and laminated top; 4" dust collection port; magnetic contractor motor control; main power switch with removable lock-out key. Actual model is: "ICS 73230"
$4,250
SAWSTOP ICS 53230-52 10" TABLE SAWSpecifications: -- 10" Blade cap., 5 HP motor, 3-1/8" depth of cut @ 0°, 2-1/4" depth of cut @ 45°, 13/16" max. dado width, 5/8" arbor diameter; blade tilt left. Features: -- Enclosed cabinet, heavy-duty belt drive, cast iron trunnions, and SAWSTOPS's revolutionary flesh detecting safety mechanism.Includes: -- 52" T-Glide Rip Fence, side support table; 4" dust collection port; miter guide. -- Magnetic contactor motor control, main power switch with removable lock-out key.
STEINEMANN OSUS NOVA 160/6 K-FS/NS-OPTIMAT Top and Bottom Calibrating Sander(6) heads consisting in 2 machines, first machine top/bottom opposed head. Secoind machine (4) head with Combi and finishing platenFeatured: -- 2-Head K, (1) top & (1) bottom; both heads directly opposed. for calibrating -- (4) head FS/NS top/bottom first Combi head, second finishing platenSpecifications:First machine Calibrating Sander: -- Top/bottom opposed single head -- Working width 1,600 mm (63") both heads 11" dia. steel contact roll -- Thickness capacity 3 - 150 mm ( 1/8" - 5.9") -- Working height (passline) 1400 mm (55") -- Cutting speed on K head 34 M/sec. (6,667 SFM) -- Tolerance within the board +/- 0,075 mm (+/- 0,003") -- 100 HP motor each head. -- 63" x 103" Abrasive belt size. (to be confirmed) -- Air jet abrasive belt tracking. -- Variable feed speed 7 - 43 M/min. (24' -138"/min.), 20 HP feed motor,. -- Control panel for this machine only Second Machine Finishing Sander: -- Top/bottom (2) head each as Combination drum/platen and finishing platen -- Working width 1,600 mm (63") both heads 11" dia. steel contact roll -- Thickness capacity 3 - 150 mm ( 1/8" - 5.9") -- Working height (passline) 1400 mm (55") -- Cutting speed on FS head 22 M/sec. (4,330 SFM) -- Cutting speed on NS head 22M/sec. (4,330 SFM) -- Tolerance within the board +/- 0,075 mm (+/- 0,003") -- No motor installed -- 63" x 103" Abrasive belt size. (to be confirmed) -- Air jet abrasive belt tracking. -- Variable feed speed 7 - 43 M/min. (24' -138"/min.), 20 HP feed motor,. -- Control panel for this machine Not included: -- infeed and outfeed conveyor -- Conveyor between the machine -- “all the control wiring goes into a cabinet that is separate on each machine. That is just the wiring for the sensors and solenoids for braking and belt tracking stuff. There are no motor controls with these so there are no starters included. The 2 head comes with (2) 150 HP motors and the 4 head has no motors on it. In order to make these operational you would need a PLC and HMI to run the controls and motor starters and would need to buy motor controls
$22,500
STETON P85 Hydraulic Cold PressSingle platen hydraulic cold press -- Platen size 1,300 mm X 2,500 mm (51" X 98") Overall platen size -- Side loading on 98" side. -- 420 mm (16.5") Max. daylight opening. -- Pressure from bottom (4) 3.34" diameter upstroke hydraulic pistons. 2 HP hydraulic pump. 90 PSI.
Call for Price
This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6f STRIEBIG STANDARD 5192A/875 SSD 2 6-1/4' x 13-3/4' Vertical Panel Saw (No Scoring) Specifications: Max. depth of cut 3-1/8". Blade dia. 300 mm (11.81"). Arbor dia. 30 mm (1.18"). Blade speed 4,750 RPM. Equipped with: 4.4 kW (6 HP) - 3,450 RPM Motor. Fold out shelf. Lower roller supports.
Call for Price
STRIP-TECH MODEL 3000 Wire Stripper --Motor: 3 HP, 220 or 440 volts, 3 phase --Drive: Gear Driven --Feed: Auto Feeding --Production: Approx 100 ft/minute --Machine Height: 37″ --Machine Length: 46″ --Machine Width: 18″ --Leg Construction: 2.00″ tube --Machine Wt: 580 lbs. --Wire Size: 1/8 to 3 inch O.D.
Call for Price
//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i5j STROMAB STA 3J0 4' x 9-1/2’ Pneumatic Door & Frame Clamp Specifications: Horizontally adjustable in 2-1/2” increments.
Call for Price
//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i65 STROMAB RS/7 S 400 mm (15.75") Radial Arm Saw Italian-made! Specifications: Base size 49” x 49” x 31-1/2” H. Table size: 44” x 55” x 36” H. Rip cap.: 42" Out & 24" In. Equipped with: 6 HP - 3,400 RPM Motor.
$35,000
STROUP 4' X 20' Cold PressSpecifications: -- 50" x 244" End Loading, Segmented, Bag press with motorized daylight opening. -- (2) Individually actuated, 50" x 122", segmented platens. -- Single air bag per platen with approx., 50 PSI specific pressure. -- Motorized adjustable daylight opening from 9" to 56". -- End loading with (2) rows of spring-loaded pop-up rollers in lower platen for easy loading/unloading of the press.
SULLAIR S-ENERGY 2209D AC 30 HP Rotary Screw Air Compressor, with 39,568 Run Hrs. (As of 7/25/24) & Built-In Dryer?Specifications: -- Cap. 127 CFM. -- Operating pressure 125 - 135 PSI. -- Max. operating temperature 235° F.Equipped with: -- 30 HP 1,770 RPM Motor. -- Ethernet connection for remote monttoring. -- Sound enclosure. -- "WS" Digital controller, with LCD Display & Touchpad. Complete with: -- Built-In Refrigerated Dryer.
SULLAIR - LS12-60- HH/A/SUL, ...Rotary Screw Air CompressorSpecifications & features: -- 60 HP - 1,770 RPM Motor, rotary screw air end, 150 max. PSI, 250 ACFM; (2) asymmetrical lobe profile rotors, only make contact on a lubricated pitch line to virtually eliminate capacity or efficiency loss. Features: -- Tapered roller bearings on the discharge and cylindrical bearings on the inlet for high load carrying capacity, pressurized fluid lubrication & cooling of the compressor with rigid piping and tubing; efficient 2-stage air/oil separation with replaceable element. Complete with: -- Spin on fiberglass fluid filter; Heavy Duty inlet air filter. -- Capacity modulator stabilizes system pressure and matches output to demand (minimizes need for Air Receiver & reduces wear caused by start/stop). -- Electromechanical gauges & controls, air aftercooling; mounted on a steel frame bed with fork cutouts. -- (73,500) Total operating hours.
SULLAIR 10B-50 ACAC Rotary Screw Compressor (Open Type)Specifications: -- 50 HP - 1,770 RPM Motor, rotary screw air end, 100-110 max. PSI, approx. 180 ACFM; (2) asymmetrical lobe profile rotors only make contact on a lubricated pitchline to virtually eliminate cap. or efficiency loss. -- Equipped with: -- Tapered roller bearings on discharge and cylindrical bearings on inlet for high load carrying capacity. -- Pressurized fluid lubrication & cooling of Compressor with rigid piping & tubing; efficient 2-stage air/oil separation with replaceable element. -- Spin-on fiberglass fluid filter, Heavy Duty inlet air filter, cap. modulator stabilizes system pressure and matches output to demand (minimizes need for air receiver & reduces wear caused by start/stop). -- Includes: -- Electro-mechanical gauges & controls, air after-cooling.
SULLAIR ES8-30H/A 30 HP Single-Stage Fluid Rotary Screw Air Compressor, with 53,186 Run & 49,602 Load Hrs. (As of 11/2023)Specifications: -- Cap. 111 ACFM. -- Rated pressure 60 - 125/135 PSIG. -- Noise level 85 dBA.Equipped with: -- E-Profile rotor design air end. -- 30 HP 3,530 RPM Motor. -- Air-cooled aftercooler. -- SULLAIR “SUPERVISOR II DELUXE"; Microprocessor controller & graphic monitor system, with LCD Display, Touchpad, Constant pressure & temperature readout of pressure, Power failure auto restart, & Automatic start/stop.
Call for Price
SULLAIR LS-10, 30 HP SCREW AIR COMPRESSOR: -- Specifications:30 HP Motor, rotary screw air end, approx. 115 PSIG - 125 PSIG max; Mounted upon 150 Gal. receiver tank.Approx. Dimensions: 64" x 32" x 65"; Approx. Weight: 2,500 lbs. -- 2,630 Approx. total operating hours. Hour meter: Inoperable.
Call for Price
SULLIVAN PALATEK D185PJD AIR COMPRESSOR (GAS/DIESEL): -- Specification:Mobile Air Compressor with JOHN DEER 4024TF281A, 2.4 L (4) cylinder diesel engine; PINTLE hitch. 29-Gal single fuel tank, 210 CFM (5.9 m³/Min.) @ 100 PSIG., idle speed 1,650 RPM, full load speed 2,500 RPM. -- Equipped with:Tapered roller bearings, adjustable pressure from 70 - 100 PSIG. large, 108 mm & 127 mm dia. twin screw air end & automatic 0 - 100% capacity control, with two stage dry type air filter, oil level sight gauge.One-piece canopy removable in a matter of minutes for ease of serviceability and maintenance. Pitched roof to allow water drainage, meets 2010 US EPA sound requirements. 15" Wheels with steel belted radial tires. -- (1,893) Hours on the unit.
Call for Price
SUMMIT PR-9S 2-Ram Horizontal Baler -- Motor: 60 HP. -- Main Cylinder: 9". -- Eject Cylinder: 8". -- Feed Opening: 60" x 44" x 46". -- Cranston Wire Tie. -- Infeed Conveyor. -- Loaded onto your Truck.