DUST-EX HSAG-24 Packaged Safety Solution for a 22"x22" (24" dia. round equivalent) Return Air Rated for 10,000 CFM. System for mitigating fire and explosions in combustible dust environments, for the woodworking industries. Generally includes Abort Gate, Non -Return Valve and Spark Detection/Suppression Hardware and Controls as follows: -- 1.) VigiFlap Dust Sensor, Dirty Air 22": Sensor, dust level, adjustable capacitive for organic dust, requires intrinsic safety system (will not trigger combustion or ignition in gasses or fuels). -- 2.) VigiFlap Explosion Isolation Flap Valve (Non-Return) Valve, EV-VF22 (EPDM); 22" diameter, flanged inlet and outlet, locking mechanism; welded steel construction, safety red painted finish, domed flap (stainless steel), inspection/access door, EPDM gasket, grounding straps, inductive shutdown sensor, normally open or closed flap orientation, certified ATEX EN 16447, NFPA 69 compliant. -- 3,) Control Panel. One-Zone CP05 Control Panel 1 inlet, 1 outlet: UL698A Control Panel for use with NFPA 69 compliant Explosion Isolation Valves. Standard panel includes status lights, intrinsically safe circuit (1 Per Zone), monitored inputs (3 total), ability to add a secondary clean air isolation valve, output for system shut down and monitoring, drawings, installation instructions, NEMA 4 outdoor rated enclosure, UL and Canada UL listings. Allows for 120VAC or 24VDC input power. -- 4,) SPARK DETECTION & EXTINGUISHING, SINGLE ZONE, KIT for pipe sizes 20?- 40? diameters; includes Raptor Spark RS-CUSP1L Control Panel, (2) Spark Detectors, Extinguishing Kit, Flexible hoses, Audible Alarm & Warning Light. Single zone spark detection and extinguishing kit for duct sizes of ?20" - 39" diameter, RS-KIT02, includes Raptor Spark RS-CUSP1L control panel, (1) RS-PDK02 packaged detector kit with (2) spark detectors with mounting kits, (1) RS-PWE02 water extinguishing assembly with hose connections and spray nozzles, audible alarm, warning light, battery back up - ATEX certified, CE listed, FM approved. -- 5.) Packaged External Test Lamp Kit, RS-TLK02, duct sizes: 6" - 39" diameter, (2) RS-SD02 test lamps with (2) RS-MK02SD/TL mounting kits - IP 65 enclosure, ATEX certified, CE listed, FM approved. -- 6.) Optional Start up Service Assistance: a.) Start Up - Day Rate @ $1,750/day. b.) Travel Service: Day Rate @ $900/day. c.) Travel Expenses: Total $110/hr. - min. two hrs. required - total $220. c.) Start Up Service Hourly Rate is $160/hr. Min. (4) hrs. needed for a total $640. -- 7.) High Speed Abort Gate, EM-HSAG02-24, magnetic (24 VDC), 22" x 22" flanged inlet and outlet (24" round equivalent), control panel for, magnet power with status lights and manual test button, gate position verification monitoring, manual reset lever, weather hood with bird screen. Maximum volume and velocity: 10,000 CFM / 3000 FPM, clean air installations only, NFPA compliant when installed with listed spark detection system. -- 8.) Packaged dust probe

DUST-EX HSAG-24 Packaged Safety Solution for a 23"x23" (24" dia. round equivalent. Suitable for up to 25" dia. ) Return Air Rated for max 12,850 CFM @ 3,500 FPM.. System for mitigating fire and explosions in combustible dust environments, for the woodworking industries. Generally includes Heavy Duty Abort Gate, Non -Return Valve and Spark Detection/Suppression Hardware and Controls as follows: -- 1.) VigiFlap Dust Sensor, Dirty Air 22": Sensor, dust level, adjustable capacitive for organic dust, requires intrinsic safety system (will not trigger combustion or ignition in gasses or fuels). -- 2.) VigiFlap Explosion Isolation Flap (Non-Return) Valve, EV-VF22 (EPDM); 22" diameter, flanged inlet and outlet, locking mechanism; welded steel construction, safety red painted finish, domed flap (stainless steel), inspection/access door, EPDM gasket, grounding straps, inductive shutdown sensor, normally open or closed flap orientation, certified ATEX EN 16447, NFPA 69 compliant. -- 3,) Control Panel, Intrinsically Safe, CP05 - single zone, allows for installation of (1) inlet and (1) outlet explosion isolation valve(s), (3) monitored inputs per zone (two programmable), (1) intrinsic circuit with barrier and physical separation (one per zone), outputs for system shut down and monitoring, NEMA 4 enclosure, 120 VAC or 24 VDC. -- 4,) SPARK DETECTION & EXTINGUISHING, SINGLE ZONE, KIT for pipe sizes 20?- 40? diameters; includes Raptor Spark RS-CUSP1L Control Panel, (2) Spark Detectors, Extinguishing Kit, Flexible hoses, Audible Alarm & Warning Light. Single zone spark detection and extinguishing kit for duct sizes of ?20" - 40" diameter, RS-KIT02, includes Raptor Spark RS-CUSP1L control panel, (1) RS-PDK-02 packaged detector kit with (2) spark detectors with mounting kits, (1) RS-PWE02 water extinguishing assembly with hose connections and spray nozzles, audible alarm, warning light, battery back up - ATEX certified, CE listed, FM approved. -- 5.) Packaged External Test Lamp Kit, RS-TLK02, duct sizes: 6" - 39" diameter, (2) RS-SD02 test lamps with (2) RS-MK02SD/TL mounting kits - IP 65 enclosure, ATEX certified, CE listed, FM approved. -- 6.) Optional Start up Service Assistance: a.) Start Up - Day Rate @ $1,750/day. b.) Travel Service: Day Rate @ $900/day. c.) Travel Expenses: Total $110/hr. - min. two hrs. required - total $220. c.) Start Up Service Hourly Rate is $160/hr. Min. (4) hrs. needed for a total $640. -- 7.) Heavy Duty High Speed Abort Gate, RGAG-23, magnetic , 23" x 23" flanged inlet and outlet (24" round equivalent), suitable for 21" - 25" dia., control panel for, magnet power with status lights and manual test button, gate position verification monitoring, manual reset lever, weather hood with bird screen. Maximum volume and velocity: 12,850 CFM @ 3,500 FPM, clean air installations only, NFPA compliant when installed with listed spark detection system. -- 8.) Packaged dust probe (broken bag detector) RS-PDP03, RS-MK02DP, etc. IP 65 encl

EARTH CARE PRODUCTS, INC. 10½ Ft. x 32 Ft. Triple-pass Rotary Drum Dryer System with Gas Burner;Complete with the following major components: -- 10.5 Ft. x 32 Ft. (despite the model DB-1030) Triple-pass Insulated drum. -- Trunnion Bases, and 30 HP Drum Drive. -- High efficiency Cyclone, Cyclone outlet Airlock. -- 100 HP Dryer Main Fan, and Ducting. -- 25 MM BTU Gas Burner complete with Refractory Lined Furnace and Gas Train. Notes: &#9679 The Trunnion Tracks and Trunnion Wheels are in good condition as is the drum interior. The system was renovated in 2015 and not used much after the work was done. &#9679 The equipment is still in-place.

EKSTROM CARLSON - Model EE, ...Straight Line Rip SawSpecifications: -- 30 HP Saw arbor motor. -- Max. thickness 3-1/4"; with 16"; dia. saw blade (no blade). -- 5 HP Feed Motor with feed rates infinitely variable to 280 FPM. -- (3) Lower infeed rollers are chain driven and are adjustable from 0° - 5°. -- Elongated pressure bar housing assures the proper guidance across the entire table length.Equipped with & Features: -- Spring-loaded rollers with 1 in. yield. -- Dual position and lubrication system; (2) outfeed rollers. -- Please note: Chain appears to be in very good condition.

EKSTROM / CARLSON - 18, ...Pump Sander Pump Sander with: (2) 1" Dia. horizontal spindle; 2 HP - 1,200 RPM enclosed motor; mounted on heavy cast iron pedestal. -- Complete with: Push button magnetic controls & starter; 4" dust collection port.

EKSTROM CARLSON - Model EE, ...Straight Line Rip SawSpecifications: -- 30 HP Saw arbor motor. -- Max. thickness 4-1/2"; with 16"; dia. saw blade (no blade). -- 5 HP Feed Motor with feed rates infinitely variable to 250 FPM. -- (3) Lower infeed rollers are chain driven and are adjustable from 0° - 5°. -- Elongated pressure bar housing assures the proper guidance across the entire table length.Equipped with & Features: -- Spring-loaded rollers with 1 in. yield. -- Dual position and lubrication system; (2) outfeed rollers. -- Please note: Chain appears to be in very good condition. -- 3 extra blades

ELGI EN07-125 10 HP Rotary Screw Compressor; 38 CFM @ 125 PSIG.Equipped with: -- Efficient air filtration system where air enters through a pre-filtered enclosure. -- After cooler is standard on all models to enable high efficiency TEFC, Super E, 10 HP motor operation up to 115°F ambient temperature.Complete with: -- "Neuron" controller that has been custom designed and engineered to monitor and control overall performance. -- Includes service indicators, fault alarms, safety shutdowns and a service / operational log feature for real-time feedback. -- Phase monitor, auto re-start and the ability to hook up to a RS 485 connection to monitor system remotely.Includes: -- 3-Stage efficient air-oil separation (less than 2 PPM). -- Single door access to routine maintenance points. -- Spin-on oil filter and separator elements for fast and easy routine service.6-Year Air End Warranty. - UL/cUL certified to ensure high levels of safety.Recommended option: F10104 / MICRO 50 Clean Resources F10104 / Micro 50 Clean Resources F10104 Oil/Water Condensate Separator - add;...$ 500

ELGI EG30-125 Rotary Screw Air Compressor; 40 HP - 170 CFM @ 125 PSIG40 HP Rotary Screw Compressor (Direct Drive); Air-End equipped with "eta-V" profile rotors. Equipped with: -- 4/5 Lobe combination designed to run at optimum speeds; low operating speeds for extended life, low maintenance and a reduced sound level; Intake Valve System with integrated blow down unit, solenoid controls & actuators designed for low losses. -- Optimal Capacity Control results in a direct saving on power consumption; air-oil separation with OSBIC process means oil-free air (1 PPM), per ISO standards and increasing the life of the separator element. -- Features: -- Efficient air cooling system; "Smart" cooling system maintains a lower temperature which increases the motor life, enables easy maintenance and the ducting is completely insulated internally from the other zones. -- Robust, reliable and able to perform at extreme temperatures - from cold to hot and from dry to extreme humid conditions. -- Complete with: -- Performance Control System's user-friendly intuitive backlit display for easy reading; remote monitoring through an RS485 connection; optimal pressure sensors monitor compressor internal pressure differences to optimize compressor maintenance. -- Includes: -- Phase Monitor, Auto Restart; custom designed, centrifugal type moisture separator with an automatic timer control drain which removes over 99% of bulk water from the compressed air.LIFETIME Air-End Warranty

ELGI EN07-125 10 HP ENCAP Rotary Screw Compressor w/Tank & Dryer; 38 CFM @ 125 PSIG.ELGI's 10 HP Rotary Screw Air Compressor w/20 CFM Refrigerated Dryer mounted on a 120 gal. receiver tank. -- Equipped with: 10 HP motor operation up to 115°F ambient temperature; "Neuron" controller that has been custom designed and engineered to monitor and control overall performance. -- Service indicators, fault alarms, safety shutdowns and a service / operational log feature for real-time feedback. -- Phase monitor, auto re-start and the ability to hook up to a RS 485 connection to monitor system remotely. -- Includes: 120 Gal. receiver tank, 40 CFM Refrigerated Air Dryer; single-door access to routine maintenance points. -- Spin-on oil filter and separator elements for fast and easy routine service.6-Year Air End Warranty. - UL/cUL certified to ensure high levels of safety.Recommended option: -- [F10104 / MICRO 50] Clean Resources F10104 / Micro 50, Clean Resources F10104 Oil/Water Condensate Separator - Add $ 305Designed for smaller compressed air systems. This system was designed as an economical solution for small compressed air systems, up to 125 psi. Theproduct offerings also include a factory-installed and plumbed wall bracket, reducing installation time. Replacement cartridges provide easy, no messmaintenance and offer the lowest life cycle cost in the industry.

GRAINMATIC - CP-960, ...2-Head Wide Belt Sander42" Width cap.; Drum, Platen.Head Configuration:1st Head: Spiral rubber covered contact roll, 7-7/8" dia., 20 HP motor.2nd Head: Combination Head, spiral rubber contact roll, and finishing platen; 15 HP motor.Specifications: -- 36" W x 75" L abrasive belts with air jet tracking. -- Motorized part thickness adjustment with keypad entry and LED readout; 0" - 7" opening. -- Infeed & outfeed spring loaded rubber covered holddown rolls. -- Feed Motor: 3.5 HP -- Variable feed speed: 15 - 60 FPM.Equipped with & Features: -- Infeed emergency stop bar. -- Disc brakes on sanding head motors. --12" Infeed load area. --Volt meters on sanding head motors.NOTE: Some specs need to be verified.

GRANUTECH-SATURN - 62-40, ...Dual Shaft ShredderSpecifications: -- Motors: (2) 100 HP. -- Feed Opening: 62" x 40". -- Dual Shaft with independent Driven Shafts -- Includes: Feed conveyor & discharge conveyor, extra feed hopper; an extra pulley roller that is magnetized for exit end of discharge conveyor (current pulley roller in use is nonmagnetic). -- includes: (2) Service manuals and catwalk structure.

GRANUTECH-SATURN - GRIZZLY 80, ...Grinder Granulator Specifications: -- Rotor size: 77-1/2" -- Cutting diameter: 34-1/2" -- Main motor: 300 HP -- Speed: 321 RPM -- Number of knives: 50 -- Number of stationary knives: 10 -- Rotor type: STAREquipped with: -- Vibratory discharge conveyor -- Outfeed conveyor -- Crossbelt magnet -- Aspiration system -- Replaceable AR500 housing liners -- 3,500 sq/in. screening area -- Severe duty gearboxNOTE: New bed & fly knives on the machine, and new wear liners &new screens. Control panel will be completely rebuilt with a 500 Amp disconnect, a soft start and all the controls.

GRANUTECH-SATURN - GRIZZLY 80, ...Grinder Granulator NO MOTOR, LID OR DRIVE TRAINSpecifications: -- Rotor size: 77-1/2" -- Cutting diameter: 34-1/2" -- Main motor: 300 HP -- Speed: 321 RPM -- Number of knives: 50 -- Number of stationary knives: 10 -- Rotor type: STAR

GRASS - ECOPRESS P: Boring Machine (Hinge) -- SpecificationsPneumatic tabletop unit mounted on welded frame base; hinge boring w/GRASS inserter block.(1) 3-Spindle boring head for hinges; 1 HP motor. -- Drill unit & insertion head and (2) spring loaded holddown cylinders operate pneumatically. Boring depth automatically sets to the material thickness being processed. -- Complete with: &#9679 450 x 730 mm Extruded aluminum framework table.&#9679 LH & RH material side stops. -- Actual Model: GRASS ECOPRESS P

GRASS - RAM, ...Drawer PressPneumatic Drawer Press used for pressing & inserting the GRASS SARGEN slide. -- Tabletop mount, foot pedal activation. -- NOTE: Machine is shown "as it is". Additional aluminum base frame was NOT shipped with this machine.

GRECON PJ 150/500 and PF 10-610 Finger Jointer and PressFinger jointer and Press systemSpecifications: -- Grecon Finger Joint System Including: Model PJ 150/500 Shaper -- Trim Saw 5 HP -- Shaper Head 30 HP -- Glue Application Head -- Timber Width 30 mm - 159 mm (1.2" - 6.25") -- Timber Thickness 12 mm - 80 mm (.5" - 3.15") -- Timber Length 250 mm - 1780 mm (9.84" - 70") -- Infeed Belt Conveyor 20" Wide X 34" LongAfter the Finger joint shaper: -- Manual Roll Conveyor with Rotation for Turning Workpieces 22" X 68" -- Outfeed Belt Conveyor 20" X 39" -- Driven Roll Conveyor 20" X 120" -- Powered Belt Conveyor Prior to Press 7" X 86"Model Press PJ 10/6100 Finger Joint Assembly Press: -- Maximum Pressing Length 240" -- Cut-Off Saw Motor 3HPNote: The machine will be reconditioned upon placement of order.

GREDA MITIKA V1500 5-Axes Machining Center - Milling/Routing/Boring/Turning/Sanding. -- Dimensional Capacity: - Max Working Diameter: 500 mm.- Max Working Length: 2,500 mm.- X-Axis Working Stroke: 2,700 mm.- Y-Axis Working Stroke: 375 mm.- V-Axis Working Stroke: 650 mm.- Z-Axis Working Stroke: 630 mm.- B-Axis ( Electro-spindle) Tilting: +/-90 Degrees.- A-Axis (Lathe): Endless. -- SPEEDS: - Max Advancing Speed in Rapid Mode: 75 M/Min.- Rotation Speed from 0-1,000 RPM. -- DRIVES:- Vertical Sanding Unit: 0.5 kW (0.67 HP) 3,600 RPM.- Horizontal Sanding Unit: 4 KW (5 HP) 3,600 RPM.- Milling Unit: 11 KW (15 HP) 9,000 RPM.- Turning Unit: 11 KW (15 HP) 4,500 RPM.- 4-Axis Routing Unit: 11 KW Electro-spindle (15 HP) 24,000 RPM.- (12) Position Tool Changer - HSK F 63 with 11 KW Inverter.- Milling Unit: 11 KW (15 HP) Motor - 9,000RPM with 11 KW Inverter.- Milling Diameter: 125 mm.- Milling Height: 180 mm.- Milling Shaft Diameter: 40 mm.- Vertical Turning Unit: 11 KW (15 HP) Motor - 4,500 RPM with 11 KW Inverter.- Saw-Blade Max Diameter: 300 mm.- Saw-Blade Shaft Max Diameter: 35 mm. -- Other Data: - Horizontal Oscillating Sanding Belt Length: 2,500 mm.- Vertical Sanding Belt Length: 850 mm- Independent Middle Rollers for Narrow Radius - 40 mm- Tampon Diameter: 100 m- Tampon Height: 180 mm- Tampon Shaft Diameter: 30 mm- Lathe System:- Full NC-Controlled Centre and tailstock device.- Max Loading Piece Diameter: 500 mm.- Endless Rotation as Interpolating Axis (A-Axis).- Min/Max Loading Length: 250/2000 mm.- Min/Max Cross-Section of parts to be loaded (automatic mode):40x40 mm/150x150 mm. -- Features: - (1) Gouge Unit.- Automatic Hopper Loading/Unloading System.- waste discharge conveyor belt with dust collection chute.- floor standing CNC and Electrical controls panel. -- Estimated 2,000 hours. -- Overall Dimensions/Weight: - 5,000 x 3,200 x 2,500 mm. Approx. weight 5,000 KG (11,000 Lbs.).

GREENMAX - EPS-AC-100, ...Cold Press DensifierSpecifications: -- EPS Polystyrene Foam Densifier -- Ratio: 50 to 1 -- Volume: 220 Lbs/Hr -- No Conveyor -- Loaded ont your Truck

GRIGGIO SC-1500 Table Saw Specifications: -- 60" Cut cap.; 5 HP main motor & scoring motor with 3/4" dia. arbor and 9,000 RPM blade speed; external scoring blade adjustment. -- Features: -- 0° - 45° Tilting 1" dia. main saw arbor, 16" max. blade size, 5.1" max. depth of cut, single blade speed. -- Rip-cut fence assembly adjustable to 60" max.NOTE: Dimensions and weight are approximate.

GRIGGIO G 1100 Wide belt Sander2-Head, 1,100 mm (43") width cap. -- 1st Head: Rubber covered steel contact roll, duro 85, 220 mm diameter . -- 2nd Head: Rubber covered contact roll duro 50 -- 25 HP motor to drive both head. -- 43" x 85" abrasive belts, electropneumatic abrasive belt tracking, -- Conveyor belt feed, two speed from control panel at 15 and 30 FPM, 0.4/0.7 HP feed drive, automatic conveyor belt tracking, -- 1/8" - 6-1/2" motorized thickness adjustment with LED readout & 0.75Hp gearmotor drive. --Automatic positioning of the working table, rubber covered spring loaded pressure rollers, double infeed and outfeed rubber covered rolls, infeed panel "over-thickness" sensor. --Two suction dust hoods dia. 6" (150mm),