COSTA - KBH CCCT 1350 & KH2 CCCT 1350, ...Top & Bottom Sander Line.Head Configuration:Machine #1 - "KBH CCCT" 4-Head Bottom Sander. Bottom Head #1: ~10" Dia. grooved Steel Drum, 47 HP motor. Bottom Head #2: ~10" Dia. grooved rubber covered contact drum, 47 HP motor. Bottom Head #3: ~10" Dia. grooved rubber covered contact drum, 32 HP motor. Bottom Head #4: Finishing platen, 23 HP motor.Machine #2 - "KH2 CCCT 1350" 4r-Head Top Wide Belt Sander. Top Head #1: ~10" Diameter Grooved Steel Drum, 47 HP - 460 V motor. Top Head #2: ~10" Grooved rubber covered contact drum, 47 HP motor. Top Head #3: ~10" Grooved rubber covered contact drum, 32 HP motor. Top Head #4: Finishing platen, 23 HP motor.Specifications: -- PC User interface for each machine. -- Sanding belt size: 53" x 103". -- 96" Belt conveyor in between machines. -- 20 HP Vacuum Blower for each machine's vacuum bed.

--This machine is in Auction @ https://exfactoryauctions.com/Detail/FD-230117/event/A122024$1. --Low starting bid! Equipped with: 1st & 2nd Heads: Each with 2” W Cross brush belts, 2.5 kW (3.35 HP) - 1,690 RPM Motor, Rotating belt on vertical axis supports series of pads with abrasive paper, Pads are adjustable to vary angle of contact on panel during rotation of belt, Pads with abrasive strip makes contact with workpieces from both sides as it rotates. (3) 2” Dia. Rubberized hold-down rolls, (1) before and after each cross brush belt head. 3rd & 4th Heads: Each with 62” L x 16” Dia. Brush Roll & 2.5 kW (3.35 HP) - 1,140 RPM Motor, & Horizontal angle adjustment. 2-5/8” dia x 7/8” w swivel rubber wheels before each brush roll head. (1) 2” Dia. Rubberized hold-down roll after last brush roll head. 53-1/2” W x 12’ L Vacuum feed belt, with 2.64 kW (3-1/2 HP) - 1,695 RPM Motor, Holes on 1-1/2” W & 2” L Centers, 2-1/2” Dia. Rubber-covered infeed & outfeed rolls, Motorized adjustment with Digital readout with LED Display. Control motor load meters. Complete with: Instruction Manual.

COSTA K6 WCCT 1350 4 Head Planer Sander (4) head with Planer, Drum, Drum and Combi headSpecifications: -- Front head #1 54" helical planer head 480 insert knives 34 kw or 45 hp motor, this is a removable head complete with cart for cleaning and changing knives -- Head #2 Drum currently set up with 100 grit belt 22 kw or 30 hp motor -- Head # 3 Drum with 150 grit belt 17 kw or 22 hp -- Head # 4 combi head with timed air blatter platten currently run 180 grit 14 kw or 20 hp -- Feed mat speed from 4-20 feet per minute Features: -- Capable of planning off 1/8" and sanding to 180 grit in one pass -- Uses 52-54" X 103 sanding belts --Vacuum feed mat only surfaced 2 or 3 times so PLENTY of life left in it. -- Used in small shop running no more than 5-10 hours a week, on a machine designed to run 3 shifts -- Has Air scrubber unit on the out feed to remove any additional dust Note: Machine was puirchase New in February 2016

Costa 60CT2-1150 (2)-Head, Wide Belt Sander44" width cap Drum, Combination HeadHead Co figuration 1st Head: Rubber-covered contact roll, 20 HP motor;2nd Head: Segmented polishing platen, (30) narrow segments are electronically controlled to conform to the panel shape and size to minimize veneer sand-throughs, each segment with variable pressure control, 15 HP motor.Specifications: -- Adjustable contact roll for varying thickness of abrasive belts with -- 45" x 103" Abrasive belt, electronic tracking. -- Motorized part thicknessopening on conveyor bed with digital readout, -- Variable feed speed 10 - 50 FPM with inverter drive, -- Vacuum conveyor bed assembly with 4 HP suction fan,infeed & outfeed spring loaded holddown rolls.Equipped with & Features: -- Controls mounted on the front of the machine, -- Instant shut-down safety guard, all motors with Y-Delta starters, and motor load meters.NOTE: Some spec's need to be verified

CP MANUFACTURING - S100-6-LH-US, ...Screens -- (1) System of (2) Screens -- Very lght Use -- Ordered as part of a Single-Stream Sort System that was designed to run 10 Tons/Hr -- 1-Feed Conveyor -- Each: 14,500 Lbs -- Loaded onto your Truck

CP CD1000 CAN DENSIFIER -- 900 to 1,500 Lbs/Hr capacity -- Fully automatic solid-state Controller -- Density: 40 Lbs per cu. ft. allowing 140,000 Lbs in 50' railcars or 40,000 Lbs in 40' Trailers. -- 10 HP - 3/60/208/230/460 Volt Hydraulic Power Unit

CAN-PAK - CD-3000: Complete Can Densifier -- Motor: 25 HP.Dimensions• Height: 9’-2";.• Width: 3’-10";.• Length: 13’-5";.• Machine weight: 8,000 Lbs.• Conveyor weight: 1,000 Lbs.• Conveyor: 11’-5"; High x 20-1/2"; wide x 13’ long.Specifications• 25 HP Power unit.• 460 Volt, 3-phase wiring.• Solid-state programmable controller.• Thermostatically controlled hydraulic oil cooler.• 1 Cubic yard hopper.• 120-gallon hydraulic tank.• 20-1/2"; Wide infeed conveyor with: 3/4 HP Motor. Direct drive gear reducer. Magnetic head pulley. Steel reject chute.

CP MANUFACTURING - GC100, ...Glass CrusherThe "GC100" crushes up to 7,000 pounds of glass per hour.Specifications: -- A tough, PVC-cleated belt carries the glass up the conveyor, allowing for visual inspection before it enters the crushing chamber. -- It efficiently handles up to a 4-liter container, breaking it into approx. 1-inch pieces of recyclable cullet; that lets you reduce your volume, easily fill your shipping containers - and ship maximum-weight truckloads to reduce your freight costs. -- The "GC100" works and keeps on working. It features cast chromium alloy steel crusher bars that are extremely resilient. It has a completely replaceable crushing drum liner. -- It is constructed of durable, heavy gauge steel. All you need is 115 115-volt single-phase power.FEATURES:• Heavy gauge steel construction• Cast chromium steel crusher bars (4 crusher bars included)• Replaceable crushing drum liner• Removable catch tray• Forklift slots• Shaft-mounted conveyor speed reducerCAPACITY: • Up to 7,000 Lbs/hour • Up to (600) cases/hourSPECIFICATIONS:• 4’-2"; Discharge height• 115 Volt single-phase wiring• 1/3 Cubic yard hopper• Mounted on 8"; casters• 0.5 HP Crusher motor• 0.5 HP Conveyor motor• 15’ Wide PVC cleated conveyor beltDIMENSIONS:• Height: 8’• Length: 3-3/4’• Width: 4’• Conveyor belt width: 15";• Hopper width: 6";• Weight: 1,000 Lbs

CRAFTSMAN DP-65 Drill PressSpecifications: -- Capacity: 15" -- Motor: 0.33 HP Equipped with: -- Push button control -- Stand

CRAM-A-LOT - SCR-T2-34: (3) 34-Yard Self-Contained CompactorsNOTE: Lot of (3) Specifications: -- Cylinder: (2) 4". -- Main motor: 10 HP. -- Feed opening: 41″ x 58″ (1,041 mm x 1,473 mm). -- Capacity: 34-Yard. -- Ram force: Up to 24 tons.

CRAM-A-LOT - HX-60: Closed Door Baler with Cart Dumper & Infeed ConveyorSpecifications: --The CRAM-A-LOT "HX-60 HH" & "HX" Series Balers are ideal for warehouses and designed for ease of installation, operation, and maintenance. -- CRAM-A-LOT® HH & HX Series Balers are: Built with extra Heavy-Duty construction; ideal for warehouses & recyclers who deal with large quantities of corrugated and paper products.Baler is designed for long hours of operation and can operate either manually or automatically with photocell control. Optional custom-engineered Feed Conveyors and Cart Dumper Systems efficiently control Baler feed rates for optimum performance in a complete Baling System.Standard Features include:ANSI Z245.5 Compliant: All Compactors meet or exceed ANSI Z245.5 safety standards.UL/CUL Listed Control Panels.UHMW Ram Shoes: Adjustable to assure straight tracking and readily replaceable, should the need arise.Oil Sight Gauge: Oil level at a glance.Oil Filter: Replaceable "spin-on" cartridge to keep your oil clean.Heavy-Duty Controls: NEMA 4-Rated pushbutton controls with "key lockable" start switch.Automatic single-cycle operation. -- Bale Size: 60" x 30" x 40". -- Bale Weight: Up to (OCC) 1,400 Lbs. --Throughput: (OCC) 2-1/2 Bales /Hr. -- Cylinder: 7".

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6k ROCKWELL/CRESCENT 5-Head Single Head Tenoner Equipped with: Manually-operated sliding table. (1) Top & (1) Bottom Tenon Heads, Each with 2 HP Motor, (1) Top & (1) Bottom Cope Heads, Each with 1 HP Motor, & (1) 7" Cutoff head with 1 HP Motor.

CROUCH - 81-70 ...Edge Sander (Non-Oscillating)5 HP Direct drive motor; 6" x 144" abrasive belt size; (1) 8" x 56" Platen.Equipped with: -- (1) 12" x 56" Adjustable side table and (1) 15" x 28" end table.Tables adjust vertically 5" and laterally 2-1/2". -- 8" Dia. rubber covered drive pulley and 4" dia. aluminum idle pulley.

CUMMINS - 682-FDR-036JJW, ...1000K DIESEL GENERATORSpecifications: -- Output: 480/277 / 3-Phase -- 1,000 kW -- 1,250 KVA -- 1,504 Amps -- 1,800 RPMNOTE: (299) Hours on meter in factory-built enclosure. - Available for inspection!

CURTIS - 5E2VT8-A3, ...Air Compressor, 5 HPSpecifications: -- Maximum allowable working pressure of 200 at 450 PSI.Equipped with: -- 80-Gallon Tank

DMC - 1350 RK, ...TECHNOSAND Dual Head Wide Belt Sander.(2) Heads, 52" width cap. - Head sequence: Contact sanding roll and Segmented platen. Head Configuration:1st Head: 7" (175 mm) Dia., 85 durometer rubber-covered calibrating contact sanding roll.2nd Head: Segmented finishing platen with EPICS (sectional electronic pad) with (46) electronically controlled air segments.Specifications: -- 53" x 103" Long abrasive belts with electronic tracking on all wide belt heads. -- Turbo panel blowers, timed abrasive belt air cleaners. -- DMC "Hydra 35" control, "EPICS" control for sectional platens. -- (99) Programs; graphic screen for machine configuration, +/- control on segmented platens, abrasive belt cleaners. -- Sequential automatic start-up, machine troubleshooting and self-diagnosis. -- Variable feed speed from 15 - 60 FPM (4.5 - 18 MPM), 1.5 HP feed drive, vacuum conveyor bed with 7.5 HP suction fan and motor.Equipped with & Features: -- Automatic conveyor belt tracking, infeed & outfeed holddown pinch rolls or shoes on all heads. -- 0" - 4" Motorized programmable thickness adjustment with LED readout. -- Automatic part thickness adjustment, infeed hand safety stop, outfeed emergency stop. -- Motor load meters and control console with monitor & keypad.NOTE: Message from the Seller: The machine was setup by a DMC tech. It has a new calibration roller & new bearings, rebuilt HYDRA 35 controller; currently under power, comes with dust collecting manifold and hoses, plus the machine can be loaded onto a flatbed for ...$ 600.

DMC UNISAND K (3) Bottom and (3)Top heads wide belt sander. --, 43" max. width. - Bottom Head sequence : 1st Head Contact roll, approx.18.5 KW motor- 2nd Bottom Head Contact roll, 2rd Bottom head, Combination head with roll and platen , approx.15 KW 2-speed motor, belt speed 118 m/sec. -- Bottom panel brush. -- Top Heads: 1st Top Head: Rubber covered contact roll approx. 18.5 KW motor, 2 speed, belt speed 9/18 M/Sec. adjustable contact roll with pneumatic grit adjustment. 2nd and 3rd Top Head: Combination head with Rubber covered contact roll and polishing platen, approx. 18.5 KW HP motor, adjustable contact roll with pneumatic grit adjustment.Top panel brush. -- 44"x 103" abrasive belts with electronic tracking; computer controlled set-up functions with key pad and LCD screen. -- Vacuum Conveyor feed belt with variable feed speed from 11 - 60 FPM, approx. 7.5 KW HP feed drive, automatic conveyor belt tensioning & tracking. -- Infeed & outfeed holddown pinch rolls on all heads, motorized part thickness opening with LED readout, 1/8" - 4" max opening, automatic part thickness set-up sensor. -- Complete with: Infeed safety stop, outfeed emergency stop, motor load meters, high efficiency dust extraction and control console with monitor. -- Actual model USK1350-IM3 + USK1350

D M C - UNISAND 135, ...3-Head Wide Belt Veneer & Finishing Sander. -- General Data:3-Head, 51" (1,300 mm) nominal width cap.; motorized part thickness opening with LED readout; 1/8" to 4" max. - Head sequence: Cross belt, rubber-covered Drum, Pad. Head Configuration/Specs: -- 1st Head: Cross belt with: EPICS 44 Segmented electronically controlled air platen; 2-speed abrasive belt; approx. 36/72 FPM (11/22 MPS) linear speed; driven by 19 & 24 HP motors; 6" wide x 238" (6,050 mm) long abrasive belt. Inside synchronized Chevron belt, approx. 228" (5,800 mm) long.Pad unit with pneumatic cylinders: Each acting on a high absorption felt strip; working pressure controlled via control panel. HYDRA Belt: 2' Electronic control with oscillating blower for cleaning. -- 2nd Head: Rubber-covered 45-durometer steel roll, 9.8" (250 mm) dia. with: 18 HP 2-speed motor, 52" x 103" (4,055 mm) long oscillating abrasive belt with electronic tracking; air blast abrasive belt cleaner. Belt runs approx. 3,550 FPM (18 MPS) linear speed; adjustment & indicator of working position. -- 3rd Head: Flexible Sanding Platen with: EPICS 44 Segmented electronically controlled air platens; 3-speed 24 HP motors; 52" x 103" (4,055 MM) long abrasive oscillating belt with electronic tracking, timed oscillating air blast abrasive belt cleaner.Pad unit composed of: Pneumatic cylinders, each acting on a high absorption felt strip. Working pressure controlled vial control panel. Special rails allowing a quick change of graphite cloth on pad. Interchangeable system to modify the hardness, stiffness, and profile of the contact surface. Controller: -- DMC "HYDRA 30" Upgraded computer with: Working position display modes mounted in a separate control cabinet; automatic thickness device reads and adjusts feet table height, motor load meters. Transport Belt Drive: -- Variable feed speed of 16 to 82 FPM, conveyor feed drive, infeed & outfeed holddown pinch rolls on all heads; infeed hand safety stop, outfeed emergency stop; high efficiency dust extraction and separate control console with monitor, keypad, etc. Also included: -- Cleaning brush head at machine discharge. -- High pressure vacuum blower. -- Dust manifold. -- Extended outfeed table.

DMC - UNISAND 2000-M2, ...Wide Belt Sander (2) Heads -- 53" Width cap. Drum, Platen.Head Configuration: --1st Head: 11" dia. (300 mm) Rubber-Covered Contac; (2) speeds or inverter adjustable 20 - 25 HP; Varied RPM. --2nd Head: Combination head with drum and graphite covered 2-1/2" finishing platen; 25 HP.Specifications: -- 54"x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computor controlled; set-up functions with keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with: 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with: LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, motor load meters.2-Roll infeed conveyor extension; high efficiency dust extraction.

EXTREMA DCF-327 Baghouse Dust Collector.Features a 16" inlet; unit has (3) sections with (9) socks per section. -- Filter Socks: 6" Dia. x 70-7/8" for greater air-to-filter ratio; (1) Micron filter. -- For indoor use. (Enclosed outdoor unit available). -- Excellent addition to the "DCY Typhoon" Dust Collector