HOLZ-HER 1435-SE EDGEBANDERCartridge glue system, 5 mm edge thickness cap. (up to 8 mm w/optional tooling), automatic magazine coil & strips, 3 mm PVC cap. pneumatic guillotine for coil cutoff.Workstations: -- Double motor end trim (2) 0.3 HP - 9,000 RPM motor ea.), chamfers 0° - 10° -- Universal top & bottom fine trim (for bevels from 0° - 15°) allows simultaneous bevel & profile trimming, (2) 0.8 HP - 18,000 RPM motor each; all trim motors are 0.6 kW HF - 300 Cy. -- Top & bottom PVC scraper unit for 0.8 - 5 mm radius, with air jets for blowoff. -- Top & bottom "jump" buffing (0.3 HP - 1,620 RPM ea.). -- Single feed speed 35 FPM. --Complete with: --Built-in operator control panel, outboard panel support, frequency converter, used tooling, and sound enclosure.

HOLZ-HER - 1432, ...CP/B Edgebander (Compact) -- Cartridge glue system (single cartridge system); edge thickness cap.: 0.3 to 3 mm (1/8"); max. banding height: 2"; min. panel width: 60 mm; min. length: 180 mm.Equipped with: -- Semiautomatic feed magazine; coil stock feeds automatically with guillotine cutoff; all strip stock is fed manually with pusher bar to advance the edging.Workstations: -- Single motor end trim for leading & trailing edge (trim motor recently replaced). -- Top & bottom flush/bevel trim: 1 HP - 28,000 RPM Motor ea. (recently replaced with BOSCH Trimmer motors). -- Top & Bottom buffing unit: 0.3 HP - 1,620 RPM ea. motor; equipped with: Cotton flap wheels. -- Single feed speed: 16-1/2 FPM.Complete with: -- Sound/safety enclosure; outboard panel support. - Machine is on casters.

HOLZ-HER - 1435-SE EDGEBANDER"1906" Cartridge Glue System; 5 mm edge thickness cap. (up to 8 mm w/optional tooling); automatic magazine coil & strips; 3 mm PVC cap. pneumatic guillotine for coil cutoff. Workstations: -- Double-motor end trim, (2) 0.3 HP - 9,000 RPM motor ea.; chamfers 0° - 10°. -- Universal top & bottom fine trim (for bevels from 0° - 15°); allows simultaneous bevel & profile trimming; (2) 0.8 HP - 18,000 RPM motor ea.; all trim motors are 0.6 kW HF - 300 Cy. -- Top & Bottom PVC scraper unit for 0.8 - 5 mm radius; air jets for blowoff. -- Top & Bottom "jump" buffing (0.3 HP - 1,620 RPM ea.). -- Single feed speed: 35 FPM.Complete with: Built-in Operator Control Panel; outboard panel support; frequency converter; used tooling; and sound enclosure.

HOLZ-HER 1488 TRIATHLON EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING) + LIGMATECH -ZR01 Return Conveyor -- Specifications:Working Capacity: Max. 1" (25 mm) solid wood banding. thin PVC, Veneer, HPL & 3 mm PVC cap.; 60 mm (2.37") max. panel thickness, and 140 mm (5-1/2") min. panel length.Front-End equipped with: -- Pre-milling Unit: (2) 2.2 kW (3.0 HP) - 12,000 RPM; (1) jump spindle with digital indicators for positioning. -- Gluing System: "ULTRA-GRANUPRESS" System with: Flat glue nozzle only 3° angle of approach ideal for solid wood edgebanding & "quick melt" feature. -- Automatic Edge Magazine for: Coil, strip & solid wood edgebanding with TRACTOR-BELT feed system; Heavy-Duty guillotine for 4 mm PVC. -- Pressure Section with: (3) Large dia. rollers, each w/individual pneumatic plunge and pressure control; programmable with Servo motor positioning; powered 1st roller with electronic speed control synchronized with chain feed speed.Edgebanding Workstations: -- End Trimming Unit: (2) 0.75 HP - 6,800 RPM ea. "HF" Motors with: "Uni-Point Swivel", quick change from flush 0° - 15° bevel programmable from operator panel; Servo controls. -- Flush Trimming Unit: (2) 2.6 HP - 12,000 RPM - 200 Cy HF motors; Servo controls. -- Fine/Bevel/Radius Trimming Unit: (2) 1-1/2 HP- 12,000 RPM - 200 Cy HF motors; bevels 0° - 45°, Servo controls + SIKO digital readouts. -- Corner Rounding Unit: (2) "HF" Top motors & (2) HF Bottom motors for trimming leading-and-trailing upper-and-lower edge/corners; trailing edge (4 x 3/4 HP - 12,000 RPM - 300 Cy HF motors; 2 mm or 3 mm radius cap. -- Profile Scraper Unit: "Super Duty" for positively smooth finishing thick PVC for radius range from 2 - 5 mm; vertical & horizontal tracing wheels, positioning enabled through (1) Servo motor function from Control Panel; SIKO readouts for easy setup. -- Buffing Unit: (2) Lateral buffing wheel positioning motors with Oscillating & Programmable Jump Action for cleaning & polishing of edges (two 0.25 HP - 3,600 RPM motors); tilts 0° - 5°, Servo controls.Equipped with and Includes: -- PPC 231 Controller with 15" LCD color screen: 90% of all set-ups can be adjusted from the Control Panel; programmable for a large variety of edges like solid lumber, veneer strips or coils, HPL, thin & thick PVC; line control so there are no mechanical limit switches along the chain track. -- Variable feed speed from 8 - 20 MPM (26 - 65 FPM); panel overhang beyond chain 35 mm (1.38"); features automatic track pad lubrication. -- Factory Documentation: Operating and Spare Parts Manuals. -- Actual Model is: HOLZ-HER 1488 TRIATHLON + LIGMATECH ZR01

HOLZ-HER 1327 SPRINT CLASSIC SPECIAL EDGEBANDER + EVA/PUR GLUING TECHNOLOGY: -- Note: This is a "SPECIAL MACHINE for THIN TAPE Only". -- Specifications: Features the HOLZ-HER patented dual "GLU-JET" EVA & PUR Zero Joint Technology System.Edgebanding capacity: Edge thickness min./max. 0.4 - 8 mm (0.02 - 0.31"); coiled material 0.4 - 3 mm (0.016 - 0.157").Workpiece thickness: 6 - 60 mm (0.23" - 2.36"); Workpiece width min. of 65 mm (2.56").Workpiece length: Min. 160 mm (6.29"); variable feed speed 10 - 18 MPM (33 - 59 FPM). Machine Infeed: -- "Open Space" for Pre-milling Station "1802": (2) 2.0 kW (2.68 HP) - 12,000 RPM motors.NOTE: This machine is not equipped with the Premilling Station, but it can be added. -- Edge Magazine "1903":For coil & strip processing; utilizes motion detector to ensure accurate, trouble free positioning of edge material.Exclusive "Tractor Belt Feed System": Edge guide equipped with automatic guillotine lockout for safety.3° Approach angle allows easy feeding of solid wood edges. -- Pressure Section "1913 Mot":1-Axis Servo controlled adjustment of the edge thickness.Pneumatic Plunge controlled pressure section with: (1) Large driven roller and (2) cantered idle rollers. -- Gluing System "GJ301Auto":Glue Jet Hybrid Technology: Processes "EVA" or "PUR" glue in cartridge or granulate form.Motorized programmable glue nozzle (upper glue line); height positioning. approx. 3-minute heat up time. Workstations: -- End Trimming Unit "1918P": Front & Rear; 2 x 0.45 kW (0.6 HP) - 9,000 RPM each motor.For Straight or Chamfer trimming with: "UNI-POINT Axis for "PCS" pneumatic changeover/swiveling up to 10° bevel. -- Combination Trimming Unit "1827": Top & Bottom; 2 x 0.65 kW (0.87 HP) - 12,000 RPM each motor; for T & B Flush/Bevel/Radius trimming. - "ProLock" Clamping System for rapid tool change.Manual edge radius adjustment up to 3 mm & chamfer adjustment up to 15° with a max. edge thickness of 6 mm. -- "Open Space" for 2nd T & B Trimming Unit.NOTE-1: This machine is not equipped with the 2nd T & B Trimming Unit, but it can be added. -- "Open Space"for Profile Scraping Unit "1929P". NOTE-2: This machine is not equipped with the Profile Scraping Unit "1929P", but it can be added. -- "Open Space" for Finish Scraping "1964". NOTE-3: This machine is not equipped with the Finish Scraping "1964", but it can be added. -- "Open Space"for Buffing Unit "1940". NOTE: This machine is not equipped with the Buffing Unit "1940", but it can be added. Operator Interface: -- HOLZ-HER "PPC 231" Power-PC + "Windows-like" Operating System. - 15" SVGA Flat "Touchscreen" control.USB Connection & Ethernet network connection ready; programs can be easily created and recalled at will. Graphic interface makes programming easy; icon of each unit may be brought up on the screen to show the Operator the status of the unit and the parameters that can be programmed.Edgebander can be operated manually when required, without necessity to write a program.

HOLZMA PROFIMAT HPL 500 38/16 REAR LOAD, AUTOMATIC PANEL SAW: -- Specifications: 149.6" (3,800 mm) Cutting length & pull-back; 6.7" (170 mm) max. main blade projection; 40 HP (29.8 kW) Main & 3 HP (2.2 kW) scoring motor. -- Saw carriage: Infinitely variable speed from 0 - 492 FPM (0 - 150 MPM), constant return of 492 FPM (150 MPM).Carriage is electronically & automatically controlled (cutting height & length) through the CADmatic according to the material/program being processed."Power-Loc" quick change system for fast and easy saw blade change.NC Controlled scoring saw adjustment from the control panel during operation -- Pusher Fence:Rack & pinion digital drives with AC Servos on both sides, forward speed 295 FPM (90 MPM), return speed 295 FPM (90 MPM).(7) Material clamps which open up to 6.7" (170 mm): (3) Standard clamps with two fingers & (4) clamps with one finger.(4) Trimming rakes for thin strips/scrap removal are attached at the clamps. -- Operator Interface:HOLZMA "Power Touch Control" IPC multi-tasking controller with Windows "7 PRO" + "CADmatic 4.0 PRACTIVE" operating system;Intel i5 Dual-core Processor, Intel HD graphics card, 4GB RAM, SATA 2-250GB hard drive, (6) USB ports, (1) serial port, ATI/DVI video port, Standard industrial keyboard connection,21.5" LCD "Touch-Screen" monitor with real-time moving 2D & 3D graphics (displays cutting dimensions & error diagnostic); virtually unlimited cutting dimension memory.(2) Ethernet 10/100 interface connections; downloading from office PC is possible. -- Rear of machine: Profile rails & "Combi-rollers" at 50 mm centers; (2) integrated front & cross-aligning units before cutting to prevent off-set panels within the same book. -- Front of machine: (3) Air flotation tables 85" x 31.5" (2,160 x 800 mm) with (1) central blower unit. -- Rear Lift Table:7-Ton (14,000 LBS), 4-Column electro-hydraulic powered rear lift table running lengthwise with fork cut-outs, 150" x 63" (3,800 x 1,600 mm) capacity. Powered rollers are 4.2" (107 mm) dia x 7.79" (198 mm) spacing, 39 FPM (12 MPM) infeed/outfeed speed; Feeding material from (3) sides is possible with additional roller conveyors.22" (560 mm) Max. bunk height from floor level; 30.7" (780 mm) max. bunk height with a pit or risers; -- Complete With: Holzma's Unique "EcoPlus" System offers energy savings up to 20%; Includes Standby button & IE3 energy efficiency Motors rating.Angular cross-cut fence; Automatic side pressure device integrated into the saw carriage for cross-cutting, the machine cuts left to right to the cross-cut fence.Front & rear forks electronically & automatically controlled through the CADmatic according to the material/program being processed.Min. side aligning dimension 0" (0 mm), max. side aligning dimension 149" (3,800 mm)."Power-Loc" quick blade change system for main/scoring blades. -- Options Include: &#9679 (1) Non-Powered in/out-feed staging conveyor with fork cut-outs as pictured. &#9679 Micro In-feed for thin an

HOLZMA HPP-11-32 OPTIMAT FRONT LOAD PANEL SAW:Specifications & features: 3,200 mm (126") Cutting length & pull-back behind the cutting line; 125 mm (4.9") saw blade projection; 30 HP (22.3 kW) main & 3 HP (2.2 kW) scoring motor. -- Variable saw carriage travel speed from 0 - 410 FPM (0 - 125 MPM), constant return of 410 FPM (125 MPM). -- Equipped with: Main blade 18" (450 mm) dia. and scoring blade 8" (200 mm dia.). -- Electronically controlled overhead pusher fence, rack & pinion drive on both sides by AC Servo motor; forward speed from 0 - 262 FPM (0 - 80 MPM), return speed of 262 FPM (80 MPM); equipped with (8) gripper clamps (open up to 4.7"). -- HOLZMA CADmatic Operating system; 15" color monitor (displays cutting dimensions); data input by keyboard or 1.44 MB floppy disk drive & downloading from office PC is possible. -- Control panel mounted on double swiveling arm for ergonomic positioning by the operator. -- Includes: Combi-rollers rear machine table with profile rails, rollers spaced at 50 mm centers; front with (3) air floatation tables, 85" x 26" (2,159 x 660 mm) each. -- Complete with: Angular square fence, automatic side aligner for crosscutting, (2) aligning devices on program fence; "Quick Saw Changing System" for main & scoring blade.

HOMAG EDGETEQ S-200 B EDGEBANDER (COMPACT): -- Specifications:0.4 - 3 mm (0.016 - 0.125") edge coil/strips thickness; 8 - 40 mm (0,312 - 1.6") panel thickness; 140 mm (5.5") min. panel length and 70 mm (2.75") min. panel width.Equipped with: -- Automatic Edge Magazine, for strip & coil stock, up to 3 mm PVC. -- "Heavy Duty" guillotine. -- EVA "Quick-Change" glue pot and roller application unit. 12-15 min. heat up time, re-heat - 3 Min. -- Pressure Section, 1st. roller driven plus (2) idle rollers, timed pneumatic pressure controlled. -- Feed Speed, 8 MPM. (26 FPM). Operator Interface: -- HOMAG "easyTouch" Operator Interface with 7" graphic color touch display & soft keypad. Intuitive, user-oriented navigation.20 storable programs guarantee flexibility when processing a wide variety of edge materials and changing customer requirements.Clear overview of the help and assistant functions, including the glue pot temperature or troubleshooting in plain textWorkstations: -- End Trimming: - (2) Motor @ 0.18 kW (.24 HP) 12,000 RPM on linear guides. -- Fine Trimming Unit: - Top/bottom (2) motors, 0.27 kW (.36 HP) 12,000 RPM, with (3) working positioning: (1) flush trimming, (2) trimming with overhang, (3) radius/bevel trimming. -- Open Space: For the addition of a "Quick Change" Profile Scrapping Unit. -- Buffing Unit: - Top/bottom (2) motors, 0.10 kW (0.125 HP) 2,800 RPM. Complete with:Manual adjusted top hold-down pressure beam; padded sound enclosure, isolation transformer for multiple input voltages, used tooling and Original Factory machine documentation. -- Actual Model is HOMAG EDGETEQ S-200 B.

HOMAG SAWTEQ B-400 PROFILINE 32/32 FRONT LOAD AUTOMATIC PANEL SAW: -- Specifications:Working Capacity: 122'' (3,100 mm) Rip cutting capacity; 122'' (3,100 mm) Pull back capacity. Main saw blade projection 4.3'' (110 mm) 25 HP (18.6 kW) Main saw blade & 3 HP (2.2 kW) "Post Forming" (Jump) scoring blade; Scoring saw adjustment via "CADmatic" control. -- Saw CarriageForward speed 0 - 492 FPM (0 - 150 MPM) Saw carriage reverse speed 0 - 492 FPM (0 - 150 MPM). -- Pusher Fence:Electronically controlled overhead program fence with (9) 2-finger gripper clamps; clamps open up to 110 mm (4.3").Rack & Pinion drive on both sides, forward speed up to 296 FPM (90 MPM), return speed of 296 FPM (90 MPM). -- Operator & Machine Control:HOMAG "powerTouch2" PC Front-End with "CADmatic 5.0" Operating System "designed for industrial environments"; virtually unlimited cutting dimensions memory.21" Full HD widescreen "Touch-Screen" monitor with multi-touch display, online operation from an office PC is possible. All mounted into dust sealed, air-conditioned control cabinet."Real-Time" Cutting sequences with a new 3D assistance graphic supports the operator and is intuitive to operate, which shortens the training period and reduces errors to a minimum. This results in efficient processes and steady output.Simple handling via tapping and swiping (touch functions) with Quick change between the individual sectionsCADmatic 5.0 is Tapio compatible & open for communication with other machines and software solutions.The SAWTEQ B-400 "IntelliDivide" optimizing software is Tapio-ready from installed software or directly from the tapio cloud, allowing "IntelliDivide" to recognize the machine configuration of your saw and consider it for every optimization run in the cloud, completely automatically & you have the choice -- Complete with:On-Board Optimizer; Automatic "CENTRIC" side aligner with front & rear forks holding ripped strips squarely against the right-angle fence.Max. Side aligner stroke 122'' (3,100mm): Rear support rails with non-marking roller modules.(3) Front air flotation tables 74" x 26 (1,879 mm x 660 mm). -- Options Include:(1) American M-1202-30, 6,000 lb. scissor-lift, as pictured. -- Actual model is HOMAG SAWTEQ B-400 PROFILINE 32/32 US Addition.

HOMAG AMBITION 2262 (KAL 210) PRODUCTION EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Working Capacity: Coiled stock min/max Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"). -- Panel stock min/max thickness12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence: Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station: Two3.0 kW(4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column,(2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor; includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, air jet panel blow-off device &SIKO digital counters for adjustments. -- Panel Pre-Heater: Pre-heating the panel brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures. --Quartz lamp for heating substrate edge before glue application improved edge quality and optimum bonding. -- Multi-Purpose Magazine: A multi-purpose 2-coil magazine expands capability by running coiled material, strips, and solid wood bands. -- Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panel on the edgebanding. -- Gluing System: (EVA - Hot Melt) QA 34 -Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit. -- 34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates. -- Lower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/Hr (26 Lbs/Hr) -- Pressure Section: Manual Adjustment with digital counter, (1) large 160 mm dia. driven & (6) 70 mm dia idle rollers, pneumatic pressure control depending on edgebanding material used. -- WORKSTATIONSEnd Trimming Unit HL 81: 0.8 kW(1.0 HP)x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30 deg. to straight cut. -- Rough/Pre-Trimming Unit: Top & bottom,0.55 kW (0.74 HP)x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Manually adjusted with digital counters. -- Profile/Bevel/Corner Rounding Unit FK 11: Multi function0.4 kW(0.54 HP) x 2)- 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper& lower edge, as well as trimming around the front & rear vertical edge; Servo controlled, Max. feed speed 20 MPM (65.6 FPM). -- Profile/Bevel Scraping Unit: Top & bottom for thick PVC/ABS, pneumatically activated. -- Flat Glue Scraper Unit: Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit: Top & bottom edge buffing/polishing. -- Spraying Units: Top/Bot

HOMAG AMBITION 2274 (KAL 370/6/A3) EDGEBANDER (W/PRE-MILL): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.3 - 3 mm (0.011. - 0.118"), Strip material min/max Edge Thickness 0.4 - 1 mm (0.016 - 0.039"),Panel stock min/max thickness 8 - 60 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18").Minimum workpiece width: 2.36" (60 mm) with workpiece thickness ≤ 22 mm) & 4.13" (105 mm) with workpiece thickness > 22 mm). -- Cleaning Agent Spraying Units:Top/Bottom spraying device prior to workpiece pre-milling. Designed for applying a separating agent, for easier cleaning of any residual glue on the panel. -- In-Feed Fence: Pre-heated manually adjustable in-feed fence with digital indicators. -- Pre-Milling Station:(2) 2.2 HP (3.0 kW) - 150 Hz, 9,000 RPM vertical jointing spindle motors; equipped with panel blow-off device and SIKO digital counters for adjustments. -- Panel Pre-Heat Unit: Quartz lamp for heating substrate edge before glue application. -- Edge Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material & strips. Maximum roll diameter: 400 mm & 830 mm.Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgebanding. -- Gluing System Homag Quickmelt: QA 3 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr). Ultra-fast five-minute (5) heat-up time. -- Pressure Section: Programmable (Servo), automatic pressure zone adjustment, (1) large 150 mm dia. driven & (4) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used.Workstations: -- End Trimming Unit:(2) 1 HP (0.8 kW) - 200 Hz, 12,000 RPM Motor ea. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip. Programmable (Servo). -- Rough/Pre-Trimming Unit:(2) 0.55 kW 0.74 HP (0.55 kW) - 12,000 RPM Motors, tilting range +/- 1° & counter-rotating to machine feed to prevent blowout & .Height adjustment synchronized with the top pressure-beam .With digital counters. -- Scraping Unit:Top & bottom for thick PVC/ABS, electro-pneumatic positioning & pneumatically activated. Pneumatically-controlled blow off nozzles. Height adjustment synchronized with top pressure beam. -- Flat Glue Scraper Unit:Top & bottom to remove potential glue squeeze-out, electro-pneumatic positioning in and out of the processing area & electro-pneumatically activated height adjustment synchronized with top pressure beam. -- Buffing Unit:Top & bottom edge buffing/polishing. Operator & Machine Control: -- Power Touch Control Multi-Touch Screen C

HOMAG AMBITION 2274 (KAL 370/6/A3) EDGEBANDER (W/PRE-MILL/HIGH PRODUCTION) (aka "TAPE ROCKET"): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.3 - 3 mm (0.012. - 0.125"), Strip material min/max Edge Thickness 0.4 - 1 mm (0.016 - 0.039"),Panel stock min/max thickness 8 - 60 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). Minimum Work piece length 610 mm (24").Minimum workpiece width: 2.36" (60 mm) with workpiece thickness ≤ 22 mm) & 4.13" (105 mm) with workpiece thickness > 22 mm). -- Cleaning Agent Spraying Units:Top/Bottom spraying device prior to workpiece pre-milling. Designed for applying a separating agent, for easier cleaning of any residual glue on the panel. -- In-Feed Fence: Pre-heated manually adjustable in-feed fence with digital indicators. -- Pre-Milling Station:(2) 2.2 HP (3.0 kW) - 150 Hz, 9,000 RPM vertical jointing spindle motors; equipped with panel blow-off device and SIKO digital counters for adjustments. -- Panel Pre-Heat Unit: Quartz lamp for heating substrate edge before glue application. -- Edge Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material & strips. Maximum roll diameter: 400 mm & 830 mm.Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgebanding. -- Gluing System Homag Quickmelt GA 65 / QA 65: QA 65 - EVA Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr). Ultra-fast five-minute heat-up time. -- Pressure Section: Programmable (Servo), automatic pressure zone adjustment, (1) large 150 mm dia. driven & (4) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used.Workstations: -- End Trimming Unit PK 25:(2) 1 HP (0.8 kW) - 200 Hz, 12,000 RPM Motor ea. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip. Programmable (Servo). -- Fine Trimming Unit PF20:(2) 0.54 HP (0.4 kW) - 12,000 RPM, fine trimming unit for edge overhangs at the work-piece upper & lower edge.Operator Interface: -- Power Touch Control Multi-Touch Screen Controller on separate console with 21.5" Full HD flat screen display, keyboard and mouse. Functions in Windows environment, includes fault diagnostic, OS9 real-time operating system."WoodScout", included graphic diagnostic tool designed to increase throughput and decrease down time. Graphical PLC diagnosis display of the error location in the machineCustomer-specific data base system that allows the operator to enter the reason for the error as well as the corrective measures to assist with future tro

HOMAG KAL 310/4/A3/S2 Edgebander (w/Pre-Milling): -- Specifications:Working Capacity: 0.3 - 3 mm Edge thickness cap., min. panel width 22 mm; max. panel thickness 60 mm; Dual speed -- Equipped with: Pre-Milling Unit 3481: (2) motors, 3 kW, 9000 RPM each, pneumatic controlled/jump milling spindles and adjustable, manual with digital indicator in-feed fence. -- Hot Melt Glue System "QA 34" Quick-Melt Unit: with heated glue roller; -- Edge Magazine Unit 2456: Automatic (2) coil/strip magazine, coils 0.3 - 3.0 mm. -- Pressure Section: Pressure roll section with (3) rollers, (1) large dia. driven & (2) idle rollers; with pneumatic pressure control for straight edges -- HOMATIC "NC 21" Power Control System: Controller operates in Windows-XP environment; Keypad w/LCD display, fault diagnostic, etc.; diagnostic analysis from HOMAG service support via Modem. -- Workstations:End Trimming Unit: (2) motors, 0.18 kW - 12,000 RPM each, to cut excess edge on the front & back of the panel. -- Flush/Pre-Trimming Unit 3201: Top & bottom trim station, 0.55 kW - 12,000 RPM +/- 1° angle adjustment, manual positioning with digital counters. -- Fine/Bevel Trim Unit 3216: (2) motors 0.4kW - 12,000 RPM each, manual positioning with digital counters -- Profile Edge Scraping Unit: with electro-pneumatic adjustment -- Buffing Unit 4402: Top and bottom with oscillation. (2) motors, 0.25kW, 2850 RPM -- Complete with & Features:Electronic DC brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- 80 mm Feed track pads; manually adjusted V-groove belt on top pressure beam and Sound/Safety enclosure over workstations. -- Actual Model is HOMAG KAL 310/4/A3/S2Note: This machine has a new display and a new back up one as well!

HOMAG EDGETEQ 4.5 SERVO QUICK MELT EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + EVA/PUR Gluing Technology: Specifications:RH Feed (Brandt) Configuration; 0.4 - 3 mm (0.016 - 0.125") Coil Cap.; 0.4 - 8 mm (0.016 - 0.315") edge strip cap.; 8 - 60 mm (0.32" - 2.4") panel thickness; 160 mm (6.3") min. panel length; 70 mm (2.76") min. panel width.Equipped with: Pre-Milling Station, (2) motors @ 2.25 kW (3.0 HP), 12.000 RPM, (1) clockwise & (1) counter-clockwise rotation for chip-free and clean panel edges.Equipped with diamond cutter heads. -- In-feed Fence, with servo motor positioning. -- Infrared Radiant Quartz Heating Unit between glue roller and pressure section. -- Automatic Edge Magazine, for strip & coil stock, strips 0.4 mm - 8 mm (0.016 - 0.315"), coils up to 3 mm PVC and "HD" guillotine. -- QA-65N Gluing Unit for PUR & EVA Glue, with "Quick Change" pot for maintenance, glue purging/color change. -- Pressure Section, 1st. roller driven plus (2) idle rollers, timed pneumatic pressure controlled; Motorized positioning of the Pressure Zone. -- Feed Speed, variable 8 - 14 MPM. (26 - 46 FPM), 14 MPM (46 FPM) when contour trimming. -- HOMAG "Power Touch Control, Full HD wide screen multi-touch display, keyboard, mouse, Industrial PC.PLC control according to IEC 61131 standards, USB connection at the operating panel; Ethernet connection 10/100 MBIT RJ45Work Stations: Straight/Chamfer End Trimming: - (2) Motor @ 0.35 kW (1/2 HP) 12,000 RPM, automatic indexing for straight to bevel trimming from control panel. -- Multi-Stage Fine Trimming Unit MS 40: - Top/bottom (2) motors, 0.55 kW (0.75 HP) 12,000 RPM, equipped with (2) Multi-Profile Radius cutter heads, each with (4) Carbide insert knives. (4) Profile options, Profile1, Profile2, Bevel & Flush trimming, via the program control. Includes Auto tilt feature, servo controlled to edge thickness, Nesting top copy system. -- Multi-Function Contour Trimming/Corner Rounding Unit MF-50: (2) Motor 0.4 kW (1/2 HP) 12,000 RPM, dual purpose for CR & continuous Top & Bottom edge trimming with servo motor control of the cutter.2-Position automatic indexing for 1-mil, 2-mil & 3-mil thickness. For leading & trailing edges vertical corner rounding of panels; equipped with radius cutters, HSK 25 system; 3 mm max. edge thickness. -- Scraping, Multi-Stage Profile Scraping Unit MZ 40: Top/bottom with Multi-Profile for (2) Radii. 1 mm & 2 mm or 3 mm in place of 2 mm, servo control positioning of vertical & horizontal copy wheels. PVC scrape collection box. -- Finish Scraping Unit: - Flush top/bottom on panel surface with floating insert knives. -- Buffing Unit: - Top/bottom (2) motors, 0.10 kW (0.125 HP) 2,800 RPM. Complete with:Motorized, programmable Top hold-down pressure beam; padded sound enclosure, isolation transformer for multiple input voltages, used tooling and Original Factory machine documentation. -- Actual Model is HOMAG EDGETEQ 4.5 SERVO QUICK MELT.NOTE: Pictured Return Conveyor is NOT INCLUDED

--MAKE AN OFFER---EXCELLENT CONDITION HOMAG - Centateq N-300 NBP084/VANTECH 512, ...5' x 12' CNC Flat Table Machining Center with ATC, Boring, Nesting, Infeed Roller & Outfeed Specifications: 5' x 12' x 37” H Flat table "Bridge Gantry" machine. Working Area: X-Axis 3,683 mm (145"); Y-Axis 1,550 mm (61.02"); Z-Axis 100 mm (3.9"). Travels: X-Axis 193" (4,900 mm); Y-Axis 1,965 mm (77.36"); Z-Axis 245 mm (9.65"). Positioning Speed: X-Axis 72 MPM (236 FPM); Y-Axis 62 MPM (203 FPM); Z-Axis 25 MPM (82 FPM). (2) Synchronized X-Axis drives, AC brushless drives on head, THK linear motion guides on all axes. Worktable: User-Friendly "S/C Tech MATRIX" grooved phenolic vacuum table for easy vacuum pod placement. (1) Pneumatic locator/positioning rail in X-Axis & (1) pneumatic locator/positioning rail in Y-Axis; (10) CNC-Controlled vacuum table work zones. Boring Unit: 2 HP (1.5 kW) Motor; (7) independent vertical spindles with: (4) In X-Axis & (3) in Y-Axis; variable spindle speeds 1,500 - 7,500 RPM. Machining: (1) 13 HP (10 kW) High-speed electro-spindle router with: HSK F 63 Adapter, constant duty, variable spindle speeds 1,250 - 24,000 RPM, left-hand or right-hand rotation. (1) 14-Position carousel-type automatic tool changer on left-hand side of machine. Operator & Machine Control: "powerControl" Control, with MICROSOFT "Windows" + "WoodWOP 5.0" Operating System. "powerTouch" 21.5“, 16:9 full-HD multitouch display, Ethernet, RS-232, USB ports, and remote pendant control. BECKHOFF Programmable logic control for (3/4) axes; linear, circular, & helical interpolation, Tapio-ready. Complete with: Infeed electric/hydraulic Scissor Lift platform with roller top; 4’ x 4’ transfer Roller Section with: 2-1/8” Dia. x 3/4” W wheels on 12” & 9-1/2” centers; vacuum arm with (2) 10” dia. vacuum pads; rake off-feed System; 61” W x 13’ L outfeed motorized Belt Conveyor; (2) 2018 BECKER "VTLF2.250/0 - 79" 10 HP 200 mbar Vacuum Pumps; light curtain; 6' H safety Fencing, Touch-off tool length Measuring Device. Control Cabinet Dimensions: 44" x 39" x 96" H. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

--MAKE AN OFFER!--VERY GOOD CONDITION-- HOMAG PROFILINE BOF 211/37/15/R FLAT TABLE MACHINE (ATC, BORING, C-AXIS) + LOADING/UNLOADING:" Specifications: "LOADED" 5' x 12' Flat table machine. Working Area X-Axis 3,700 mm (145.67"); Y-Axis 1,550 mm (61.02"); Z-Axis stroke 535 mm (21.06"); max. material thickness 210 mm (8.27"). Positioning Speed X & Y-Axis 80 MPM (262 FPM); Z-Axis 30 MPM (98 FPM). Worktable Table size 3,700 mm x 1,610 mm x 870 mm H (145.67" x 63.39" x 34-1/4"). (4) Front rails; (1) right-hand & (1) left-hand corner pneumatic location pins. User-Friendly "MATRIX" grooved aluminum grid vacuum table with: (2) Vacuum work zones with foot pedal controls; table zones can be used independently or together for full table area. Table accepts: Spoil board, gasket material, or vacuum pods. Boring Unit (1) 1.5 kW (2 HP) Motor; (9) independent vertical spindles with: (5) In X-Axis & (4) in Y-Axis; variable spindle speeds from 4,500 - 7,500 RPM; (4) horizontal spindles with (1 + 1) in X-Axis & (1 + 1) in Y-Axis. Machining (1) 12 kW (16 HP) Liquid cooled electro-spindle router with: "HSK 63F" Adapter; variable spindle speeds from 1,000 - 24,000 RPM. (1) CNC Controlled C-Axis for 360° horizontal processing. (1) 12-Position ride along automatic tool changer on back of head for "on-the-fly" tool changing. Operator & Machine Control "powerControl" CNC Control with: MICROSOFT "Windows" + "WoodWOP 5.0" Operating System. Includes: 17" LCD Display, Ethernet, RS-232, & USB ports, remote pendant control, (3) foot pedal controls. Complete with: SOUTHWORTH "LST8-36W" 8,000 Lbs Cap. extra wide Infeed Electric/Hydraulic Tandem Scissor Lift Platform; S/N I061700-100; platform size 60" x 144", lowered height 6-3/4", raised height 42-3/4". Vacuum Arm with: (4) 6-1/2” Dia. Vacuum pads; 61” W x 13’ L outfeed motorized belt conveyor; 2011 DEKKER "VMAX VMX0553KA1-00 40 HP oil sealed liquid ring Vacuum Pump, S/N M21128; with nominal cap. 550 CFM; max. vacuum pressure 29" Hg.; approx. oil capacity (17) gallons; minimum continuous operation 10,000 Hrs; max. noise level (at 3 ft.) 78 dBA; 40 HP - 1,775 RPM TEFC direct drive motor; "ONDEK" Touchpad Controller with LCD display; (10,918) run Hrs & dimensions: 90" x 27" x 108"; light curtain; 5’ x 17’ pressure sensitive Safety Mat. Machine Dimensions with Infeed & Outfeed: 478" x 142" x 117" H. Control Cabinet Dimensions: 50 x 32 x 96 H. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

HOMAG CENTATEQ N 300 FLAT TABLE MACHINE (W/ATC/BORING): -- Specifications: 5' x 12' Flat Table "Bridge Gantry" machine with User-Friendly "MATRIX" grooved phenolic vacuum table. -- Working Area:"X" Axis is 145.7" (3,700 mm), "Y" axis 61" (1,550 mm), "Z" axis stroke Routing is 12.8" (325 mm), "Z" axis stroke Boring is 7.3" (185 mm) max. material thickness of 3.9" (100 mm). -- Positioning speed: "X" Axis is 236 FPM (72 MPM); "Y" axis is 203 FPM (62 MPM); "Z" axis 82 FPM (25 MPM). Machine head travels on THK linear motion guides on all axes. -- Worktable: (1) Pneumatic locator/positioning rail in "X" Axis & (1) pneumatic locator/positioning rail in "Y" Axis. - (10) NC Controlled Vacuum Table work zone. -- Boring Unit:2 HP (1.5 kW) Motor, (7) independent vertical spindles with 4-spindles in "X" Axis & 3-spindles in "Y" Axis; programmable variable speed from 1,500 - 7,500 RPM. -- Machining:(1) 18 HP (13.4 kW) High-speed electro-spindle router with: "HSK F63" Adaptor; constant duty; variable speed from 1,250 - 24,000 RPM, RH or LH rotation.(1) 12-Position ATC Rack located at the LH side of the machine. -- Operator Interface:PC Front-End with: WEEKE "PC 85T" + Windows "10 PRO" + WoodWOP Operating System.21" TFT Color graphic monitor, keyboard for data entry, PC 85T hand control pendant; CD R/W & floppy drives, EtherNET interface for LAN connection to office PC, RS-232 serial interface, USB ports.BECKHOFF Programmable logic control for (3/4) axes, linear, circular & helical interpolation; the Controller is contained in a separate freestanding, dust-free control cabinet that can be placed at either the LH or RH side of the machine. -- Complete with: (2) 10 HP BUSCH Mink MV 0312 B Vacuum Pumps. Light curtain (machine will stop if the operator enters the work area). Perimeter safety devices. Separate control cabinet. Touch-off tool length measuring device. Handheld pendant control. -- Actual Model is: HOMAG CENTATEQ N 300/512.

HOMAG (OPTIMAT ABD060/12/D/NA) CNC BORE, GLUE & DOWEL INSERTER: -- Specifications: Horizontal drilling block/fixture with (3) 10 mm (0.39") Dia. Individually selectable 7,500 RPM spindles & 1.73 kW (2.32 HP) 3,420 RPM Motor, Max. drilling dia. 20 mm (0.79"), Total drill bit length 70 mm (2.76"). -- Low-viscosity glue injection system with DÜRR SYSTEMS “EcoPump AD"; Low-pressure double membrane glue pump & External flow sensor, Max. viscosity 700 mPas. -- MAFU “MRA 250"; Vibrating hopper dowel feeder. -- Working Capacity:Workpiece length 20 - 1,250 mm (0.79" - 49.2"), Workpiece width 50 - 800 mm (1.97" - 31.5"), Workpiece thickness 10 - 60 mm (0.39" - 2.36"). -- Dowel sizes 8 mm Dia. x 30 mm or 35 mm L (0.31" Dia. x 1.18" or 1.38" L). -- Work Area: Overall table size 20" x 150" with (2) Separate work fields to process up to (4) work pieces independently, Work pieces can be loaded in one field while being processed in the other field. -- Pneumatically lowering left-hand, right-hand & center stops, Distance between left-hand & right-hand stops 1,270 mm (50"), Distance between center & left/right-hand stops 620 mm (24.4"). -- Operator & Machine Control: "POWERTOUCH" 3-Axis Control with USB Port, 10/100 Ethernet Port & 21" TFT Flat screen monitor. -- WOODWOP, ABDWORK with BECKHOFF TWINCAT, MMR Data collection & Analysis, SCHULER machine data acquisition, Tapio-ready. -- Complete with:(4) 3-1/8"; x 5-1/8"; Pneumatic clamping cylinders. -- Glue nozzle cleaning system. -- HONEYWELL “HYPERION 1300G"; Barcode Scanner, with Supported barcodes: 1D – Barcode & 2D – Data matrix code.

KREG DK 3100 Electric 3-spindle Pocket DrillSpecifications: -- 1.5 HP Direct drive electric motor; 39-1/2" table/ top working height; (0.5 - 1) Sec cycle time. -- Drills (2) pocket holes in (1) machining cycle across rails of varying widths with 3/8" dia. step bit in (1) smooth operation. -- Drill spindles in the machine are fixed at 3/4" - 1" and 1-3/4" on center allowing it to handle most common rail widths of 1-1/2" up to 3-3/4" with ease. -- One of the (3) Spindles is with left-handed, simply remove one bit from the spindle not being used to set the desired 2-hole spacing. -- The bits are supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material.Features: -- 15ø Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired.Includes: -- Pressure gauge, fence, hold down, and foot pedal control.

Single belt oscillating "Tiltable Bed" 0° - 90° sander, 3 HP main motor, 3,400 RPM, belt size 6" x 89", 30.5" long platen. -- Max sanding length 30.5", 4" vertical adjustment of front table, 36" table height, oscillating rate of 121 times/min. -- Includes: (4) interchangable spindles, sizes are 1.25" - 1.5" - 2" & 2.5" dia.